Wind Damage >> Reinforcing Your Garage Door

Protecting Your Home From Hurricane Wind Damage Figure 6. Double-Wide Garage Doors Certain parts of the country have building codes requiring garage doors to withstand high winds. You should check with your local government building officials to see if there Reinforcing Your Garage Door are code requirements for garage doors in your area. 

Some garage doors can be strengthened with retrofit kits. Check with your local building supplies retailer to see if a retrofit kit is available for your garage door. You can expect to pay Reinforcing Your Garage Door from $70 to $150 to retrofit your garage door. Many garage doors can be reinforced at their weakest points. Retrofitting your garage doors involves installing horizontal bracing onto each panel. 

This horizontal bracing can be part of a kit from the garage door manufacturer. You may also need heavier hinges and stronger center supports and end supports for your door (see Figure 6). 3 Check the track on your garage door. With both hands, Reinforcing Your Garage Door grab a section of each track and see if it is loose or if it can be twisted. 

If so, a stronger track should be installed. Make sure that it is anchored to the 2´ 4s inside the wall with heavy wood bolts or Reinforcing Your Garage Door properly attached to masonry with expansion bolts (see Figure 7). Figure 7. Garage Door Track Anchoring After you have retrofitted your door, it may not be balanced. To check, lower the door about halfway and let go. 

If it goes up or down, the springs will need adjusting. The springs are dangerous and should be adjusted by a professional. If you are unable to retrofit your door, Reinforcing Your Garage Door you can purchase specially reinforced garage doors designed to withstand winds of up to 120 miles per hour. 

These doors can cost from $400 to $450 (excluding labor) and should be installed by a professional. Storm shutters Installing storm shutters over all exposed windows and Reinforcing Your Garage Door other glass surfaces is one of the easiest and most effective ways to protect your home. You should cover all windows, French doors, sliding glass doors, and skylights. 

There are many types of manufactured storm shutters available. For more information on manufactured shutters, check with your local building supplies retailer. If you install manufactured shutters, Reinforcing Your Garage Door follow the manufacturer’s instructions carefully. Before installing shutters, check with your local building official to find out if a building permit is required. 

It is important that you have your shut ters ready now, and that you mark and store them so they can be easily installed during a hurricane watch. Plywood shutters that you make yourself, if installed properly, Reinforcing Your Garage Door can offer a high level of protection from flying debris during a hurricane. Plywood shutters can be installed on all types of homes. 

Measure each window and each door that has glass, and add 8 inches to both the height and Reinforcing Your Garage Door width to provide a 4-inch overlap on each side of the window or door. Sheets of plywood are generally 4´ 8 feet. Tell your local building supply retail er the size and number of openings you need to cover to determine how many sheets to buy. 

To install plywood shutters you will need bolts, wood or masonry anchors, large washers, and 5/8 inch exterior-grade plywood. For windows 3 feet by 4 feet or smaller installed on a wood frame house, Reinforcing Your Garage Door use 1/4-inch lag bolts and plastic-coated permanent anchors. The lag bolts should penetrate the wall and frame surrounding the window at least 1 3/4 inches. 

For larger windows, use 3/8-inch lag bolts that penetrate the wall and frame sur rounding the window at least 2 1/2 inches. For win dows 3 feet by 4 feet or smaller installed on a masonry house, Reinforcing Your Garage Door use 1/4-inch expansion bolts and galvanized permanent expansion anchors. The expansion bolt should penetrate the wall at least 1 1/2 inches. 

For larger windows, use 3/8-inch expansion bolts that penetrate the wall at least 1 1/2 inches. The tools you will need are a circular or hand saw, a drill with the appropriately sized bits, Reinforcing Your Garage Door a hammer, and a wrench to fit the bolts. To be safe, use eye protection and work gloves. 4 Cut the plywood to the measurements for each opening. 

Drill holes 2 1/2 inches from the outside edge of the plywood at each corner and at 12-inch intervals. Drill four holes in the center area of the plywood to relieve pressure during a hurricane. Figure 8. Plywood Storm Shutters Place the plywood over the opening and Reinforcing Your Garage Door mark each hole position on the outside wall (see Figure 8). 

Drill holes with the appropriate size and type of bit for the anchors. Install the anchors, the plywood, and the bolts to make sure they fit properly. On wood-frame houses, Reinforcing Your Garage Door make sure that the anchors are secured into the solid wood that frames the door or window and not into the siding or trim. 

Mark each shutter so you will know where it is to be installed and store them and the bolts in an accessible place. If the opening is larger than one sheet of plywood, you will need to make shutters with 2´ 4 bracing. This bracing can be two 2´ 4s at the middle and bottom of the two sheets of plywood, evenly spaced, Reinforcing Your Garage Door with the 2-inch side attached to the inside of the storm shutter.

 Attach the 2´ 4s to the outside of the storm shutter with 2-inch, 10-gauge wood screws before installing the shutter. Figure 9. Large Plywood Storm Shutters 5 The recommendations in this brochure are not intended to replace local building code requirements or Reinforcing Your Garage Door to serve as the only options for protecting your home from hurricane wind damage. 

For more information on protecting your home from hurricane wind damage, contact your local building official; your local building supply retailer; Reinforcing Your Garage Door or a building professional, such as an engineer, architect, or experienced contractor. ARC 5023 FEMA 247 Dec. 1993

Vermiculite Insulation

Protect Your Family from Asbestos Abatement Vermiculite Insulation Asbestos-Contaminated Vermiculite insulation Insulation This page provides important information on how to protect yourself and your family i  read more..

Do It Yourself Restoration Of Mold Damage On Paper

Although it is neither necessary nor desirable to remove all dirt or discoloration from old papers, surface cleaning sometimes improves the appearance of an artifact. Surface cleaning can also remove substances that might eventually damage paper, or that could be transferred to other papers during h  read more..

Mold Remediation

Living in a home that has a crawlspace is fine there are thousands of houses across the United States that are built above the ground for whatever reason and have crawlspaces. Along with the many responsibilities of being a homeowner the crawlspace should be checked periodically, maybe mark i  read more..

Flood Damage

You come home and you hear water running and the first thing you think to yourself, ,"my basement has been flooded." Now, of course, having water in your basement is more than just a nuisance, it can be a health issue. Especially, if your basement includes finished living areas. When you have   read more..

Lead Paint Testing

Lead is a naturally appearing element that’s found in small quantities in the earth’s crust. While Lead Paint Removal Lead Paint Testing does have some beneficial purposes, it could be poisonous to humans and animals causing serious health problems. Lead could be found in all parts of our surroundings.   read more..

Guidelines For Fire And Smoke Damage Repair

If you suspect someone has heat stroke, follow these instructions: Immediately call for medical attention. Get the person to a cooler area. Cool the person rapidly by immersing him/her in cool water or a cool shower, or spraying or sponging him/her with cool water. If the humidity is low, wrap the p  read more..

How To Dispose Of Asbestos Siding In Texas

This mandatory appendix specifies the procedure for analyzing air samples for asbestos and specifies quality control procedures that must be implemented by laboratories performing the analysis. The sampling and analytical methods described below represent the elements of the available monitoringÂ&n  read more..

Hurricane Roof Damage

Experts describe the following progression during gable-end collapse: typically, the gable-end popped out due to suction on the leeward side of the building and the loss of sheathing, or Wind Damage Hurricane Roof Damage to a combination of suction and increased pressure resulting from breached openings in the shell.&  read more..

Crime Scene Cleanup Business Information

OSHA believes that the requirements set forth in this final standard are those, based on currently available data in the record, which are necessary and appropriate to provide adequate protection to employees exposed to blood and Crime Scene Cleanup Crime Scene Cleanup Business Information other potentially infectious materials. 
  read more..

How To Get Rid Of Sewage

Overhead Sewers. The basement floor drain and any plumbing fixtures in the lower levels of your house that have experienced backups will be disconnected from the sewer system. Plumbing from those fixtures will be re-routed to a sealed tank. Inside the tank,an ejector pump lifts the waste water up se  read more..