Wind Damage >> Reinforcing Your Garage Door

Protecting Your Home From Hurricane Wind Damage Figure 6. Double-Wide Garage Doors Certain parts of the country have building codes requiring garage doors to withstand high winds. You should check with your local government building officials to see if there Reinforcing Your Garage Door are code requirements for garage doors in your area. 

Some garage doors can be strengthened with retrofit kits. Check with your local building supplies retailer to see if a retrofit kit is available for your garage door. You can expect to pay Reinforcing Your Garage Door from $70 to $150 to retrofit your garage door. Many garage doors can be reinforced at their weakest points. Retrofitting your garage doors involves installing horizontal bracing onto each panel. 

This horizontal bracing can be part of a kit from the garage door manufacturer. You may also need heavier hinges and stronger center supports and end supports for your door (see Figure 6). 3 Check the track on your garage door. With both hands, Reinforcing Your Garage Door grab a section of each track and see if it is loose or if it can be twisted. 

If so, a stronger track should be installed. Make sure that it is anchored to the 2´ 4s inside the wall with heavy wood bolts or Reinforcing Your Garage Door properly attached to masonry with expansion bolts (see Figure 7). Figure 7. Garage Door Track Anchoring After you have retrofitted your door, it may not be balanced. To check, lower the door about halfway and let go. 

If it goes up or down, the springs will need adjusting. The springs are dangerous and should be adjusted by a professional. If you are unable to retrofit your door, Reinforcing Your Garage Door you can purchase specially reinforced garage doors designed to withstand winds of up to 120 miles per hour. 

These doors can cost from $400 to $450 (excluding labor) and should be installed by a professional. Storm shutters Installing storm shutters over all exposed windows and Reinforcing Your Garage Door other glass surfaces is one of the easiest and most effective ways to protect your home. You should cover all windows, French doors, sliding glass doors, and skylights. 

There are many types of manufactured storm shutters available. For more information on manufactured shutters, check with your local building supplies retailer. If you install manufactured shutters, Reinforcing Your Garage Door follow the manufacturer’s instructions carefully. Before installing shutters, check with your local building official to find out if a building permit is required. 

It is important that you have your shut ters ready now, and that you mark and store them so they can be easily installed during a hurricane watch. Plywood shutters that you make yourself, if installed properly, Reinforcing Your Garage Door can offer a high level of protection from flying debris during a hurricane. Plywood shutters can be installed on all types of homes. 

Measure each window and each door that has glass, and add 8 inches to both the height and Reinforcing Your Garage Door width to provide a 4-inch overlap on each side of the window or door. Sheets of plywood are generally 4´ 8 feet. Tell your local building supply retail er the size and number of openings you need to cover to determine how many sheets to buy. 

To install plywood shutters you will need bolts, wood or masonry anchors, large washers, and 5/8 inch exterior-grade plywood. For windows 3 feet by 4 feet or smaller installed on a wood frame house, Reinforcing Your Garage Door use 1/4-inch lag bolts and plastic-coated permanent anchors. The lag bolts should penetrate the wall and frame surrounding the window at least 1 3/4 inches. 

For larger windows, use 3/8-inch lag bolts that penetrate the wall and frame sur rounding the window at least 2 1/2 inches. For win dows 3 feet by 4 feet or smaller installed on a masonry house, Reinforcing Your Garage Door use 1/4-inch expansion bolts and galvanized permanent expansion anchors. The expansion bolt should penetrate the wall at least 1 1/2 inches. 

For larger windows, use 3/8-inch expansion bolts that penetrate the wall at least 1 1/2 inches. The tools you will need are a circular or hand saw, a drill with the appropriately sized bits, Reinforcing Your Garage Door a hammer, and a wrench to fit the bolts. To be safe, use eye protection and work gloves. 4 Cut the plywood to the measurements for each opening. 

Drill holes 2 1/2 inches from the outside edge of the plywood at each corner and at 12-inch intervals. Drill four holes in the center area of the plywood to relieve pressure during a hurricane. Figure 8. Plywood Storm Shutters Place the plywood over the opening and Reinforcing Your Garage Door mark each hole position on the outside wall (see Figure 8). 

Drill holes with the appropriate size and type of bit for the anchors. Install the anchors, the plywood, and the bolts to make sure they fit properly. On wood-frame houses, Reinforcing Your Garage Door make sure that the anchors are secured into the solid wood that frames the door or window and not into the siding or trim. 

Mark each shutter so you will know where it is to be installed and store them and the bolts in an accessible place. If the opening is larger than one sheet of plywood, you will need to make shutters with 2´ 4 bracing. This bracing can be two 2´ 4s at the middle and bottom of the two sheets of plywood, evenly spaced, Reinforcing Your Garage Door with the 2-inch side attached to the inside of the storm shutter.

 Attach the 2´ 4s to the outside of the storm shutter with 2-inch, 10-gauge wood screws before installing the shutter. Figure 9. Large Plywood Storm Shutters 5 The recommendations in this brochure are not intended to replace local building code requirements or Reinforcing Your Garage Door to serve as the only options for protecting your home from hurricane wind damage. 

For more information on protecting your home from hurricane wind damage, contact your local building official; your local building supply retailer; Reinforcing Your Garage Door or a building professional, such as an engineer, architect, or experienced contractor. ARC 5023 FEMA 247 Dec. 1993

Remove Black Toxic Mold From The Attic

Although the level of personal protection suggested in these guidelines is based on the total surface area contaminated and the potential for remediator and/or occupant exposure, professional judgment should always play a part in remediation decisions. These remediation guidelines are based on the s  read more..

Animal Control California

Generally, mountain lions are calm, quiet and elusive. They are most commonly found in areas with plentiful prey and adequate cover. Such conditions exist within Hollister and San Benito County. Mountain lions are an important part of the ecosystem, helping to keep deer and other prey populations in  read more..

Ceiling Leak From Storm

Coastal A zones are not shown on present day Flood Insurance Rate Maps (FIRMs) or mentioned in a community's Flood Insurance Study (FIS) Report. Those maps and studies show zones VE, AE, and X (or older designations V1-30, A1-30, B, and C). Therefore, until Coastal A Zone designations Structural Drying Ceiling Leak From Storm   read more..

How To Restore Water Damaged Pictures

Libraries, archives, museums, and historical societies are responsible not only for collecting, interpreting, and exhibiting significant materials that document history, but also for the long-term preservation, security, and accessibility of these Document restoration How To Restore Water Damaged Pictures materials.

The American Associa  read more..

How To Protect A Home In A Flood Plain

Clothing and LinensEven if your washing machine didnot get wet, do not use it untilyou know that the water is safeenough to drink and that yoursewer line works. (Perhaps afriend or relative has a washingmachine you can use until yours isclean and working.) Flood Damage How To Protect A Home In A Flood Plain

Befor  read more..

Will Acrylic Primer Seal Lead Paint

The engineering controls and work practices associated with the employee's job assignment including training of employees to follow relevant good work practices described in Appendix B of this section; The contents of any compliance plan and Lead Paint Removal Will Acrylic Primer Seal Lead Paint the location of regulated areas in effect.   read more..

What To Do If Hardwood Floors Have Flood Damage

If your house is being flooded by lowing waters entering through windows, doors or other openings, you can temporarily seal those openings to keep the water out.Make or purchase metal or wooden shields to it the openings. Secure the shields to the openings with bolts or Flood Damage What To Do If Hardwood Floors Have Flood Damage slide them into special   read more..

Asbestos Abatement Training

The asbestos awareness training that is provided by OSHA is for workers in a number of different industries, including the construction industry to gain knowledge about the risks of Asbestos Abatement Asbestos Abatement Training. The employees working in the manufacturing industry are also at risk for a significant amount of exposure  read more..

Flood Water Cleanup

What if I have already consumed potentially contaminated water? Illness is possible, especially for people that already have a chronic illness or may have compromised immune systems, for example, from AIDS or cancer treatments. This is why Water Damage Flood Water Cleanup boil water notices are issued. 
  read more..

Asbestos Flooring

Question 1: Are we correct that Asbestos Abatement Asbestos Flooring floor tile cleaning activities (normal maintenance such as stripping and buffing operations) are covered under both the Asbestos flooring General Industry Standard (§1910.1001) and the Asbestos flooring Construction Standard (§1926.1101)?  <  read more..