Animal Damage >> Bee Removal

Removing a nest of bees can be a challenging and dangerous undertaking, the utmost caution is advised. If you do not possess the right kind of equipment or the know-how this job might be well served to be left to the professionals. Depending on which part of the country that you live in, because in some areas they have bees that are Africanized. But if it you’re a do-it-yourselfer, and feel very confident about performing a Bee Removal then here are some tips.

  1. Let's talk about some of the things you'll need when performing a Bee Removal. You'll need a professional be suit, the gloves beekeepers wear along with the helmet and veil. You'll need the smoker and smoker fuel, you'll also need some window screen or fine mesh hardware cloth. First things first, put on your bee suit, your helmet and veil and your gloves before getting close to any bee nest. Use your smoker to make the bees lethargic, once the bees look very docile and nonthreatening the careful procedure of Bee Removal can be done.
  2. Carefully cut away the bee nest from whatever it is attached to, this may take some doing as not to damage the nest. Bees serve a very important function, and as time goes by there are fewer and fewer bees every year. We do not want to upset the very delicate balance of nature, without these bees our flowers and our agricultural crops will be in jeopardy. That's why is very important to be careful when performing a Bee Removal
  3. There is a certain way of lighting the bee smoker, first tear a half sheet of black print newspaper into one is strips packing the strips loosely into the base of the smoker the glossy newsprint paper found in magazines contain inks that might give off smoke with chemicals that could harm the bees. Put the newspaper strips in the bottom of the smoker and light them with a candle lighter or long matches. Squeeze the bellows gently several times until the flames have spread to the majority of the newspaper.
  4. Continue on with the Bee Removal by dropping loosely wanted pile of burlap twine upon the flames in the smoker. If the burlap twine his role to tightly it will make it difficult to light the twine and keep it lit. Use a spackling knife to press the twine deeper in the smoker until the level of the twine is burning is below the rim. Take some low residue woodchips or pellets this will make the smoker burn longer and more evenly.
  5. The Bee Removal should take about 20 to 30 minutes, the bees should remain lethargic this whole time and shouldn’t pose any problems. After the bees have been safely removed take green grass and stuff it into the spout lid until the smoke stops coming out in the flames go out. Allow the canister to cool for at least 20 minutes after the spout has been blocked.

Wind Damage To Trees

Wind damage to trees AL FERRER SEMINOLE COUNTY URBAN HORTICULTURIST The impact of hurricanes on trees varies from simple defoliation to broken branches, split branch crotches and trunks, leaning or falling trees. While no tree can be guaranteed to stand up to hurricane-force winds, there are some tr  read more..

Removal_Tree Removal Insurance

If FEMA cannot deliver the needed technical expertise, the odds increase that costs and eligibility of debris removal will become problematic during the recovery phase of the disaster. Communities may be forced to evaluate and select debris removal and monitoring contractors without possessing the n  read more..

Hurricanes Damage

Hurricanes are from the cyclone family, but just in the more tropical part of the country. They typically have torrential rains and constant winds of about 74 miles per hour or more which blow in a counter-clockwise way around a center or better known as the "eye". Emergency Board up Hurricanes Damage winds could surpass 15  read more..

Commercial Building Drying And Mold

MOLD/WATER DAMAGED MATERIALS Key Engineering Controls and Work Practices Discard all water-damaged materials, materials that are visibly coated with mold that cannot be properly cleaned, such as porous materials (e.g., carpeting, drywall, insulation), and Structural Drying Commercial Building Drying And Mold materials that have been wet   read more..

How To Write To A Renter To Clean Up A Rental

Thermostat Settings.During spring/summer season (May - September) the thermostat should be set on"cool/auto" at 80 degrees. During the heating season (October - April) the thermostat should be set on "heat/ auto" at 65 degrees. All electrical circuit breakers should be left "on" at move-out. Du  read more..

Flood Insurance Rate Map

Zone AO: Areas subject to inundation by 1-percent-annual-chance shallow flood insurance rate map (usually sheet flow on sloping terrain) where average depths are 1–3 feet. Average Flood Damage Flood Insurance Rate Map depths derived from detailed hydraulic analyses are shown within this zone. Mandatory flood insurance rate map ins  read more..

How To Remove Soot Smoke Smell

Standard on Protective Ensembles for Technical Rescue Operations,2007 Edition The NFPA 1951, 2007 Edition contains performance requirements for a CBRN Technical Rescue Protective Ensemble for use during entry into CBRN atmospheres not Immediately Dangerous to Life of Health (IDLH). 
This   read more..

Flood Damage

The reason of this article is to offer supervision in regards to techniques for Structural Drying Flood Damage under the usual industry standards. This article presumes some basic knowledge on the part of the reader, but experience to a water damage situation could be helpful. If you have flood insurance they will gener  read more..

Mold Remediation

Living in a home that has a crawlspace is fine there are thousands of houses across the United States that are built above the ground for whatever reason and have crawlspaces. Along with the many responsibilities of being a homeowner the crawlspace should be checked periodically, maybe mark i  read more..

How To Restore Fire Damaged Electronics

The project shall minimize the usage of any commercial parts for all grade levels. There are no controls in commercial industry that are imposed uniformly upon all manufacturers to build in a common acceptable quality level. While many manufacturers maintain good quality controls, Electronic Restoration How To Restore Fire Damaged Electronics oth  read more..