Mold Remediation >> How To Clean Mold

Fungi and Bacteria in Ventilation Systems Fungi growing in ventilation systems may contaminate indoor environments and cause a variety of problems. Some fungi can cause lung infections. Many fungi can cause allergic reactions in susceptible people and respiratory irritation in non-allergic people.Inhalation of fungal spores by highly susceptible people can have How To Clean Mold fatal consequences. 

Some environmental bacteria can grow in ventilation systems, but these are rarely a threat to healthy people. They can, however, How To Clean Mold be a nosocomial problem. Low levels of airborne fungi can be a primary or contributing cause of Sick Building Syndrome (SBS) and poor Indoor Air Quality (IAQ). The photomicrograph at the right shows lung tissue infected with a growing mycelium of aspergillus. 

Fungi differ significantly, in certain respects, from most other airborne pathogens, such as bacteria, viruses, How To Clean Mold and protozoa. Fungi do not cause secondary contagious infections; only the person inhaling the fungi is at risk. Fungi can exist outdoors and enter the building through the air intakes. No other respiratory pathogens can exist outdoors -- viruses and bacteria are carried and transmitted indoors by human or animal hosts, with anthrax being the one exception. 

Fungi are normally harmless and non-parasitic. Fungal infections inevitably result from fungi being in the wrong place, How To Clean Mold often as the result of poor cleanliness or improper design of ventilation system components. Fungi are actually plants that contain no chlorophyll -- see this chart. The true fungi are the Eumycetes. 

Some of the fungi, the mushrooms, yeasts and some of the molds are extremely beneficial to us. They assist the production of cheese, antibiotics, yogurt, wine and beer. Some fungi, like the blights, can cause extensive crop damage. Dutch Elm disease is, How To Clean Mold in fact, a fungus. In buildings, the ones that cause problems when they get into the wrong place are usually certain of the ascomycetes. 

Airborne Pathogenic Fungi Only certain fungi can produce infections, and only a few of these have been noted to travel via the airborne route, or become entrained in the airflow of intake ducts. The following chart list those fungi which are of primary concern: Fungi from Outdoors Fungi produce spores, in much the same way as bacteria do, How To Clean Mold and this enables them to survive harsh conditions while they travel or lie dormant. 

Spores are usually what enter the building air intakes How To Clean Mold and what can travel through the ventilation airstream. Fungal spores are smaller than fungal cells and can vary in size from 1 micron to 100 microns. A well-maintained HEPA filter should be capable of intercepting the vast majority of fungal spores. At the right is an image of a colony of Candida albicans that has produced a number of large and small spores. 

Fungi are ubiquitous in the outdoors, but occur in high concentrations only in hot Southern climates, especially during dry spells. Florida, Louisiana, Texas, New Mexico and southern California often experience high seasonal mold spore levels. Generally, How To Clean Mold when the ground dries after a period of moisture, the winds can overturn the top layers of soil and disperse large quantities of mold spores. 

These can be carried aloft into urban areas, where they are drawn into air intakes How To Clean Mold and building ventilation systems. The photo at left shows the long growing branches of mycelium that are characteristic of Nocardia asteroides, from a sputum sample of an infected patient. Nocardia are bacteria called actinomycetes, which greatly resemble fungi in characteristics, and they also produce spores. 

Even though the problem is more common in southern states, it only takes the right conditions for microscopic quantities of fungi to gain a foothold in a ventilation system. This situation has occurred across the US, regardless of climate. Many, How To Clean Mold if not most, cases of poor IAQ and SBS can be tied directly to the occurrence of mold spores either in the ventilation ducts, or in the walls of buildings. 

Sometimes, fungi are merely a contributing factor when the ventilation is inadequate -- normal levels of airborne fungi are not removed from the building air. Dealing with Fungi in Ventilation Systems Filtration provides the primary defense against fungal spores entering a building ventilation system. Pre-filters can be effective against most fungi, How To Clean Mold even when in the spore form. 

If a higher degree of protection is required, HEPA filters can be very effective, provided they are tightly installed, How To Clean Mold and well maintained. Fungus can grow on HEPA filters as well as other ventilation components and, if unchecked, can actually contribute to the problem. The image at right shows a layer of actinomyces mycelium growing on a surface. 

Fungus or fungal spores from the outdoors can be dealt with easily, as described above. If, however, the fungus is already growing inside the building or ventilation system, How To Clean Mold the problem becomes somewhat more difficult. Fungi require moisture for growth. The source of the moisture must be identified and then controlled. 

Cooling coils, drains pans, and water pans for humidifiers are likely locations for fungal growth, How To Clean Mold especially when there is standing water. These must be treated as necessary with proper disinfectants. Some systems provide built-in UVGI lights for continuous disinfection. These components should be disassembled and cleaned with a strong disinfectant, such as chlorine, when fungal or bacterial growth is found. 

Clogged drains are often a cause for standing water. Condensation on ductwork or other components is another likely source of moisture. The ductwork must be inspected for fungal growth How To Clean Mold and cleaned with a disinfectant. The cause of the condensation must be identified. Often, it results from inadequate insulation, or leakage into, or out of, the ductwork. 

Sometimes return air can leak into the supply air duct and result in localized condensation. Sometimes the insulation itself can absorb and hold moisture, resulting infungus growth that may then directly or indirectly produce contamination of the building air. Smoke tests, How To Clean Mold or airflow measurements, and/or pressure tests can determine duct leakage. 

In the absence of water they may reduce to spore form, which makes them even more subject to air entrainment. Therefore, How To Clean Mold a cycle of condensation and dehydration may exacerbate a fungal dispersion problem. In this case, the problem might be perplexing to isolate -- sometimes the duct and components will appear dry, while cases of respiratory irritation or infection may occur in irregular cycles that could ultimately depend on humidity variations. Every situation can be unique and must be studied carefully.

Flood Damage

You come home and you hear water running and the first thing you think to yourself, ,"my basement has been flooded." Now, of course, having water in your basement is more than just a nuisance, it can be a health issue. Especially, if your basement includes finished living areas. When you have   read more..

Wood Peckers Starlings Sparrows And Chimney Swi

The NHPA requires: 1) federal agencies to evaluate the effects of any federal undertaking on cultural resources, 2) consult with the State Historic Preservation Office regarding the value and management of specific cultural, archaeological and historic resources, and 3) consult with appropriate Amer  read more..

How To Make A Dry Basement Waterproofing

The results reported in Appendix B for the modeled energy savings show the same patterns as those for a foundation wall with no rim joist and no above-grade exposure. Specifically, the first R-5 of insulation produces a significant basement energy savings of 52% with only an additional 12 % of   read more..

How To Do Foreclosure Clean Outs

Debris Contractor Oversight Team (DCOT): A team created of in house force account labor and/or contractors to oversee and monitor debris removal operations by debris contractors. This team monitors the debris removal process from pickup to final destination at a permanent landfill. Debris Control Zo  read more..

Is Lead Certification Required For Lead Paint Remo

Lead Certification Required for Lead Paint Removal. There are some situations in which you are legally required to be CDPH Lead-Related Construction (LRC) certified. Even if certification is not required in your situation, CDPH encourages you to become trained and Lead Paint Removal Is Lead Certification Required For Lead Paint Remo certified to help pr  read more..

How To Pass A Radon Inspection

In announced tests, applicants must conduct all exposures and analyses in the same way that they are done for consumers. For example, device analyses must be done by the participating organization using equipment used in analyzing consumer measurements. Applicants must pass a test for each spec  read more..

Remove House Fire Smoke Odor From Clothes

In areas where fires are likely to occur, state and local public health agencies should consider running pre-season public service announcements (PSAs) or news releases to advise the public on how to prepare for the fire season. PSAs should be simple (e.g., the season for wildfires is approaching; t  read more..

Mold Remediation

The following are the minimum steps that shall be applied to all Document restoration Mold Remediation projects, and for smaller, minor restorations that could be in non-sensitive, unoccupied areas such as the flooded regions that have involved personal, single dwelling homes. This information will help you understand how a p  read more..

Withstanding Wind And Lightning

Rooftop Attachment of Lightning Protection Systems in High-Wind Regions Hurricane Katrina Recovery AdvisoryFEMA May 2006, Revised July 2006 Purpose: To recommend practices for installing lightning protection systems (LPS) that will enhance Wind Damage Withstanding Wind And Lightning wind resistance in high-wind regions. Key Iss  read more..

Naturally Remove Smoke After A Fire

During a fire, soot agglomerations are segregated in the air due to flotation effects, the larger agglomerations dropping out of the air closest to the fire and the finer agglomerations farther from the fire. Soot particles will penetrate the finest crevices of a surface and remain physically trappe  read more..