Mold Remediation >> Kill Mold On Flooded Basement Walls

Pumping Out a Flooded Basement If your basement is flooded, don’t rush to pump it out. Water in the ground outside your house is pushing against the outside of your basement walls, and the water inside is pushing right back. If you drain your basement too quickly, the pressure outside the walls will be greater than the pressure inside, which may cause the basement floor and Kill Mold On Flooded Basement Walls walls to crack and collapse. 

How to Safely Pump Water Out of Your Basement: Never go into a flooded basement unless you know the electricity is off. For insurance purposes, Kill Mold On Flooded Basement Walls take pictures of your basement before beginning any work. When the water is no longer covering the ground around the perimeter of your house, you can begin pumping the water from your basement.  

CAUTION: Do not use gasoline-powered pumps or generators indoors as they produce deadly carbon monoxide exhaust fumes. Pump the water level down 2 to 3 feet, mark the water level, Kill Mold On Flooded Basement Walls and wait overnight. Check the water level the next day. If the water went back up and covered your mark, it is too early to drain your basement.  

Wait another 24 hours. Pump the water down 2 to 3 feet again, and check the water level the next day. When the water stops rising, Kill Mold On Flooded Basement Walls pump the level down another 2 to 3 feet and wait overnight. Repeat the above steps until all the water is pumped out of the basement. What to Do After Draining Your Basement:  

Shovel out as much mud as you can as quickly as possible. The mud left behind by floodwaters poses a health hazard, Kill Mold On Flooded Basement Walls and it is a lot easier to remove before it dries out. Hose off the walls and floors with clean water and then disinfect them with a solution of 1 ½ cups of liquid chlorine bleach to a gallon of fresh water. 

CAUTION: NEVER mix bleach and ammonia cleaning products. This will produce deadly chlorine gas! Remove the vents or registers of heating and air conditioning ducts, Kill Mold On Flooded Basement Walls the wall covers for wall switches and outlets that were flooded. Clean and disinfect them as above. All flexible ducting, including dryer connections, must be replaced for health protection.  

Check your water system, including drains and utility connections, for leaks, breaks, Kill Mold On Flooded Basement Walls and loose fittings. Have your water supply checked for any contamination. This service may be provided by your local health department. Before turning on the electricity, check your incoming electrical service for any damage. 

Replace any wiring, switches and/or outlets that were submerged or got wet during the flood. This may require the services of a professional. Cleaning Up and Drying Out Your Home If your house Kill Mold On Flooded Basement Walls or its under structure have been under water from recent flooding, you will need to take important steps to clean out bacteria and mold and to dry the building out thoroughly. 

Steps for Drying Out the House: Turn off the main power. Open up the house to allow moist air to escape. Remove all wet furniture, contents Kill Mold On Flooded Basement Walls and carpets or rugs. If you decide to keep some of these items they must be cleaned and disinfected. Discard all contaminated food products. For more information see our Food Safety page. 

Interior Walls: Interior plaster walls will need to be drained if they are still holding water. Remove the baseboard trim Kill Mold On Flooded Basement Walls and drill holes about 2" above the floor to let the water out. The holes can be hidden behind the reinstalled baseboards. Flood soaked sections of wallboard will usually have to be removed and thrown away. 

Paneled walls can usually be dried out by prying out the bottom corner of the paneling Kill Mold On Flooded Basement Walls and propping it out away from the wall studs. Exterior Walls: Insulation in exterior walls will hold moisture and bacteria. It is important to remove any flood soaked insulation as soon as possible so the other building materials can dry out properly. 

Batt insulation and blown-in insulation cannot be reused in your repairs and must be thrown away. Rigid foam insulation can be removed Kill Mold On Flooded Basement Walls and disinfected. Once it is completely dry it can be reinstalled in the wall cavity. Once the insulation is removed the wall must be disinfected and thoroughly dried. Dehumidifiers and portable heaters can speed this process up. 

Floor Framing: If the flood waters got into your floor framing but not into your house you will need to check for wet floor insulation. Wet floor insulation must be removed and the framing disinfected Kill Mold On Flooded Basement Walls and dried out in the same manner as the walls. Disinfecting: Disinfect all surfaces that were soaked by flood waters with "disinfecting" or "sanitizing" products. 

An alternative is to use a mixture of 1/4 cup liquid chlorine bleach mixed into one gallon of water. Remove mildew using household mildew removers or Kill Mold On Flooded Basement Walls fungicides. CAUTION: NEVER mix bleach and ammonia cleaning products. This will produce deadly chlorine gas! Reconstruction: Reconstruction materials should be water resistant so instead of regular wallboard or plaster, use water resistant or waterproof wallboard for interior wall surfaces. 

Install wallboard horizontally. Some additional tips: Use rigid foam insulation instead of batt Kill Mold On Flooded Basement Walls or blown-in insulation. Use galvanized or stainless steel hardware. Use indoor-outdoor carpeting. Use exterior grade plywood for sub-floor reconstruction. The Problem With Mold One problem that often occurs after a flood is the development of mold. 

Mold growths, or colonies, Kill Mold On Flooded Basement Walls can start to grow on a damp surface within 24 to 48 hours. Molds digest organic material, eventually destroying the material they grow on. In addition to the damage molds can cause in your home they can also cause mild to severe health problems. 

If your home has water damage due to flooding, sewage backup, plumbing or roof leaks, damp basements, Kill Mold On Flooded Basement Walls overflows from sinks or bathtubs, or high humidity, mold and mildew will develop within 24-48 hours of water exposure. Even worse, it will continue to grow until steps are taken to eliminate the source of moisture and effectively deal with the mold problem.

Get Rid Of The Dead Mice Smell In Vents

Occasionally a raccoon, skunk, tree squirrel, or other animal will find a suitable shelter in or under a house, shed, or other structure. These animals may occupy an area sporadically, using the site only two or three consecutive days or nights usually until available food sources are exhausted. How  read more..

Tenant Eviction Notice

Tenants who receive a housing subsidy or live in a federal or state housing project may have rights in addition to those provided by state law. For example, the U.S. Department of Housing and Urban Development (HUD) or Tenant Move Out Cleanup Tenant Eviction Notice the Alaska Housing Finance Corporation (AHFC) may control rent inc  read more..

Black Mold Exposure

Although the largest group of patients had diffuse pulmonary infiltrates, a significant fraction had focal pulmonary disease, meningitis, Mold Remediation Black Mold Exposure or other extrapulmonary disease. Six patients had only a positive serologic test with no other evidence of infection. Excluding the patients who ha  read more..

Flood Protection Methods

Illinois can flood in any season. Floods have been caused by localized storms, rain over severaldays on saturated ground, snow melt, and ice jams. Over the last two decades, Flood Damage Flood Protection Methods a significant floodhas occurred somewhere in the state each year.

Many of them received a state or federa  read more..

What Is Needed To Be A Crime Scene Technician

Sometimes total electrical isolation is a good thing— and that's the idea behind a power-over-fiber (PoF) communications cable being developed by Sandia engineers. "It's common to isolate communications between systems or devices by using fiber optic cables, but if power is required, Crime Scene Cleanup What Is Needed To Be A Crime Scene Technician   read more..

Lead Paint Exposure To Iron Workers

Field measurements using a tape measure of 12 of the cuts revealed that the paint was stripped back an average of 1.15 (range of 0.5 to 4.0 inches) inches from the cut line (based on 69 measurements taken). After hot cutting, Lead Paint Removal Lead Paint Exposure To Iron Workers burned paint provided visual evidence that stripping was insuffi  read more..

How To Clean A Carpet After A Sewer Backup

When a sewer overflows, it is usually the result of inappropriate materials in the sanitary sewer system. Please help prevent sewer back-ups and overflows!Sewer Backups The sanitary sewer system is the network of underground pipes that carry wastewater from your sinks, Sewage Cleanup How To Clean A Carpet After A Sewer Backup toilets, showers, bathtub  read more..

How To Remove Tiles With Asbestos

Preparing the Work Area Disabling HVAC Systems: The power to the heating, ventilation, and air conditioning systems that service the Asbestos Abatement How To Remove Tiles With Asbestos restricted area must be deactivated and locked off. All ducts, grills, access ports, windows and vents must be sealed off with two layers of plastic to   read more..

Biggest Tornado Disasters

A downburst cluster itself is made up of several downbursts. A downburst is an area of strong, often damaging wind produced by a convective downdraft with the overall size of the downburst varying from 4 to 6 miles (8 to 10 kilometers). Within the downbursts are microbursts; Wind Damage Biggest Tornado Disasters smal  read more..

How To Survive A Hurricane

Foundations are at relatively low risk from wind forces, but are at higher risks from water forces in wave erosion zones and flood zones. In flooding and wave erosion zones, Wind Damage How To Survive A Hurricane homes are typically elevated above base flood elevation (BFE), defined as the elevation having a 1% chance of b  read more..