Lead Paint Removal >> Lead Paint Exposure To Iron Workers

Field measurements using a tape measure of 12 of the cuts revealed that the paint was stripped back an average of 1.15 (range of 0.5 to 4.0 inches) inches from the cut line (based on 69 measurements taken). After hot cutting, Lead Paint Exposure To Iron Workers burned paint provided visual evidence that stripping was insufficient (Figure 2). 

Visual observation and XRF measurements confirmed that eight of the 40 segments to be cut (the inside corner pieces) had not been stripped at all, Lead Paint Exposure To Iron Workers since the XRF readings were no different from readings taken in the painted areas. The XRF was needed to confi rm lack ofstrip- ping since new primer paint had been applied,making it difficult to visually determine which areas had been stripped. 

Personal Sampling Results The eight-hour TWA lead exposure for day one was 3898 ¹g/M3 , Lead Paint Exposure To Iron Workers or 78 times the OSHA Permissible Exposure Limit (PEL) of 50 ¹g/M3 . The task-specifi c exposure level during hot cutting on day one was 11,271 ¹g/M3 (166-minute TWA); this involved cutting on both stripped and unstripped steel. 

The eight- hour TWA lead exposure on day two was 4027 ¹g/M3 (81 times the PEL). The task-specifi c exposure level when working on the stripped steel was 670 ¹g/M3 (91-minute TWA). In contrast, Lead Paint Exposure To Iron Workers the exposure level when working on the unstripped steel in the corners was 30,000 ¹g/M3 (63-minute TWA) (Table I). 

Personal Protection Observations The ironworker was wearing a half- mask, air-purifying respirator with "pancake" style P-100 filters, welder's helmet, foam earplugs, and heavy welder's gloves (Figure 1). At the end of day two, Lead Paint Exposure To Iron Workers small holes were found in the P-100 respirator pancake filters, apparently due to welding sparks. 

The filter material at the inhalation valve gasket was discolored on one of the filters. These holes and Lead Paint Exposure To Iron Workers the discoloration indicated at least partial failure of the filter. Discussion Air Sampling Results This was a very limited industrial hygiene survey in which a single iron- worker was monitored over two successive days of hot cutting on stripped steel. 

However, the survey illustrates that several factors may contribute to high lead exposures experienced by ironworkers. First, Lead Paint Exposure To Iron Workers the so-called stripped areas may be stripped back significantly less than the Cal/OSHA required four inches on both sides of a cut line. Second, difficult to reach corners may not be stripped at all. 

If these results are typical of exposures to ironworkers working on bridges, then minimum respiratory protection should be half-mask, Lead Paint Exposure To Iron Workers supplied-air respirators in positive-pressure mode, as initially required by the Lead in Construction Standard for highest exposure trigger tasks. 

The results of short-term lead exposure monitoring during hot cutting on stripped and Lead Paint Exposure To Iron Workers nonstripped areas indicate that hot work on .75-inch steel which has been stripped back only 1.15 inches from the cut line creates signifi cantly less exposure than work on unstripped steel (670 ¹g/M3 vs. 30,000 ¹g/M3 ). 

However, cutting of the stripped areas results in exposure levels that exceed the maximum use concentration (MUC) of the half-mask respirator that this iron- worker was wearing (MUC D 10 £ PEL), Lead Paint Exposure To Iron Workers if sustained over an eight-hour shift. Further studies are indicated to determine whether hot work on steel that is stripped back the required minimum of four inches reduces exposure to airborne levels less than the PEL. 

XRF Results The XRF was a useful tool for determining which areas were adequately stripped and Lead Paint Exposure To Iron Workers which were not. Visual observation, on the other hand, would have been inadequate in locating the unstripped corner areas identifi ed by the XRF, since these areas had been newly primed with the same gray primer (non lead-based) as the stripped areas. 

The XRF also detected that the lead was located primarily in the deepest (red- colored) original paint layers. The XRF was somewhat useful as a gross qualitative tool in determining which elements were present besides lead (iron and fiinc) and which elements were below its detection limit (arsenic, chromium, manganese, Lead Paint Exposure To Iron Workers and nickel below a DL of 500 ppm; mercury below a DL of 100 ppm). 

Laboratory results for arsenic (<50 ppm) concurred with the XRF readings (<500 ppm). However, Lead Paint Exposure To Iron Workers the laboratory analysis for chromium (1900 ppm) did not agree with the XRF reading (<500 ppm). This discrepancy casts some doubt on the usefulness of the XRF as a metals-screening tool. In addition, cadmium and beryllium could not be measured with this model XRF due to the interference from the cadmium radiation source. 

Respiratory Protection Inadequacies Hot work on bridges is often viewed incorrectly as a low-lead or nonlead activity, Lead Paint Exposure To Iron Workers since industrial painters have supposedly stripped back the steel before the ironworkers arrive. In this instance, the ironworker had only a half-mask, air-purifying respirator available. 

Iron- workers performing hot work on structures with high concentrations of lead in the paint should be required to wear air supplied respirators in positive-pressure mode initially. Moreover, Lead Paint Exposure To Iron Workers sparks may burn holes in respirator filters, reducing their effectiveness. Multi-Employer Challenges 

Lead exposure issues are magnified at a multi-employer worksite consisting of many layers; in this case, the state department of transportation, general contractor, painting subcontractor, and ironworker subcontractor. First, the government agency responsible for bridge repair may be reluctant to play a strong role in worker safety, Lead Paint Exposure To Iron Workers fearing that intervening in contractor affairs makes them liable in the case of a third-party injury suit. 

Second, the general contractor, with overall responsibility for safety and health conditions at the worksite, may shortchange safety in the interest of production. Finally, Lead Paint Exposure To Iron Workers the ironworker, arriving on the site after the painters have left, may discover that the stripping is inadequate, but decide to complete the job anyway. Further, the ironworker may be an owner or operator, as in this survey, and may not be covered by OSHA regulations.

Leaking Toilet Base

Burst Pipe Floods Basement Areas On the front page...Late Tuesday evening, June 26, the Clinical Center experienced one of the worst floods in its history when a water booster pump vibration eliminator on a chilled- water pipe burst and ran for 40 minutes before it was detected Water Damage Leaking Toilet Base and st  read more..

Once A Hurricane Or Major Storm Hits

Once a hurricane or major storm hits, it's too late to protect your home and property. But there are things you can do now to limit future wind damage. Some are fairly simple and inexpensive; others will require a contractor. You'll need to consider the characteristics of your home, Wind Damage Once A Hurricane Or Major Storm Hits y  read more..

How To Protect A Washer Dryer From A Flood

If there are no signs of problems, Flood Damage How To Protect A Washer Dryer From A Flood turn the power off again.Plug a lamp or small appliancein an outlet on the circuit youjust tested, or turn on a lightswitch. Be sure that the appliance you are using to test eachoutlet is working properly.

5.Turn the power  read more..

Smoke Damage From A House Fire

Damaged, or "mutilated" currency may be mailed or personally delivered to the Bureau of Engraving and Printing. When mutilated currency is submitted, a letter should be included stating the estimated value of the currency and an explanation of how the currency became mutilated. Each case is carefull  read more..

How To Clean Trash Out Of Foreclosure Homes

While most renters can have their tenancies terminated for a variety of reasons, the law says that mobilehome park tenants can be evicted from the park only for these reasons:91 the tenants are behind in space rent and Tenant Move Out Cleanup How To Clean Trash Out Of Foreclosure Homes don't pay even after receiving a 7 day written notice from theland  read more..

Lawn Damage From Raccoons And Skunks

Relationship of This Environmental Assessment to Other Environmental Documents has issued a Final Environmental Impact Statement on the national APHIS/Animal Damage Lawn Damage From Raccoons And Skunks program. Pertinent information avai  read more..

How To Dehumidify A Water Damaged House

Dehumidification with Climate Changer™ Air Handlers Triple the amount of water removed The Trane ™ desiccant dehumidification system is Dehumidification How To Dehumidify A Water Damaged House an award winning method for controlling space humidity. A desiccant wheel is configured in series with the cooling coil to significantly improv  read more..

How To Repair A Fire Damaged Wood Floor

Each year the National Fire Protection Association’s (NFPA) Standards Council recognizes individuals for outstanding service to the organization in the development of codes and Fire Damage How To Repair A Fire Damaged Wood Floor standards. Awards will be presented to 35 individuals at the World Safety Conference & Exposition ® taking   read more..

If You Are Exposed To Lead Poisoning

If you are exposed to lead above the PEL, or if you are exposed to lead compounds such as lead arsenate or lead azide which can cause skin and eye irritation, your employer must provide you with protective work clothing and equipment appropriate for the hazard. If work clothing is provided, it must   read more..

Lead Paint Removal Is Hazardous

When you are medically eligible to return to your former job, your employer must return you to your "former job status.” This means that you are entitled to the position, wages, benefits, etc., you would have if you had not been removed. If you would still be in your old job if no removal had occ  read more..