Wind Damage >> Protect Your Doors Against Wind

Certain parts of the country have building codes requiring garage doors to withstand high winds. You should check with your local government building officials to see if there are code requirements for garage doors in your area. Some garage doors can be Protect Your Doors Against Wind strengthened with retrofit kits. 

Check with your local building supplies retailer to see if a retrofit kit is available for your garage door. You can expect to pay from $70 to $150 to retrofit your garage door. Many garage doors can be reinforced Protect Your Doors Against Wind at their weakest points. Retrofitting your garage doors involves installing horizontal bracing onto each panel. 

This horizontal bracing can be part of a kit from the garage door manufacturer. You may also need heavier hinges and stronger center supports and end supports for your door (see Figure 6). Check the track on your garage door. With both hands, Protect Your Doors Against Wind grab a section of each track and see if it is loose or if it can be twisted. 

If so, a stronger track should be installed. Make sure that it is anchored to the 2×4s inside the wall with heavy wood bolts or properly attached to masonry with expansion bolts (see Figure 7). After you have retrofitted your door, it may not be balanced. To check, Protect Your Doors Against Wind lower the door about halfway and let go. 

If it goes up or down, the springs will need adjusting. The springs are dangerous and should be adjusted by a professional. If you are unable to retrofit your door, Protect Your Doors Against Wind you can purchase specially reinforced garage doors designed to withstand winds of up to 120 miles per hour. 

These doors can cost from $400 to $450 (excluding labor) and should be installed by a professional. Storm shutters Installing storm shutters over all exposed windows and other glass surfaces is one of the easiest and most effective ways to protect your home. You should cover all windows, Protect Your Doors Against Wind French doors, sliding glass doors, and skylights. 

There are many types of manufactured storm shutters available. For more information on manufactured shutters, check with your local building supplies retailer. If you install manufactured shutters, Protect Your Doors Against Wind follow the manufacturer's instructions carefully. Before installing shutters, check with your local building official to find out if a building permit is required. 

It is important that you have your shutters ready now, and that you mark and store them so they can be easily installed during a hurricane watch. Plywood shutters that you make yourself, Protect Your Doors Against Wind if installed properly, can offer a high level of protection from flying debris during a hurricane. Plywood shutters can be installed on all types of homes. 

Measure each window and each door that has glass, and Protect Your Doors Against Wind add 8 inches to both the height and width to provide a 4-inch overlap on each side of the window or door. Sheets of plywood are generally 4×8 feet. Tell your local building supply retailer the size and number of openings you need to cover to determine how many sheets to buy. 

To install plywood shutters you will need bolts, wood or masonry anchors, large washers, and 5/8 - inch exterior-grade plywood. For windows 3 feet by 4 feet or smaller installed on a wood frame house, Protect Your Doors Against Wind use 1/4-inch lag bolts and plastic-coated permanent anchors. The lag bolts should penetrate the wall and frame surrounding the window at least 1 3/4 inches. 

For larger windows, use 3/8-inch lag bolts that penetrate the wall and frame surrounding the window at least 2 1/2 inches. For windows 3 feet by 4 feet or smaller installed on a masonry house, Protect Your Doors Against Wind use 1/4-inch expansion bolts and galvanized permanent expansion anchors. The expansion bolt should penetrate the wall at least 1 1/2 inches. 

For larger windows, use 3/8-inch expansion bolts that penetrate the wall at least 1 1/2 inches. The tools you will need are a circular or hand saw, a drill with the appropriately sized bits, Protect Your Doors Against Wind a hammer, and a wrench to fit the bolts. To be safe, use eye protection and work gloves. Cut the plywood to the measurements for each opening. 

Drill holes 2 1/2 inches from the outside edge of the plywood at each corner and at 12-inch intervals. Drill four holes in the center area of the plywood to relieve pressure during a hurricane. Place the plywood over the opening and Protect Your Doors Against Wind mark each hole position on the outside wall (see Figure 8). Drill holes with the appropriate size and type of bit for the anchors. 

Install the anchors, the plywood, and the bolts to make sure they fit properly. On wood-frame houses, Protect Your Doors Against Wind make sure that the anchors are secured into the solid wood that frames the door or window and not into the siding or trim. Mark each shutter so you will know where it is to be installed and store them and the bolts in an accessible place. 

If the opening is larger than one sheet of plywood, you will need to make shutters with 2×4 bracing. This bracing can be two 2×4s at the middle and bottom of the two sheets of plywood, Protect Your Doors Against Wind evenly spaced, with the 2-inch side attached to the inside of the storm shutter (see Figure 9). 

Attach the 2×4s to the outside of the storm shutter with 2-inch, 10-gauge wood screws before installing the shutter. The recommendations in this brochure are not intended to replace local building code requirements or Protect Your Doors Against Wind to serve as the only options for protecting your home from hurricane wind damage. 

For more information on protecting your home from hurricane wind damage, contact your local building official; your local building supply retailer; or a building professional, Protect Your Doors Against Wind such as an engineer, architect, or experienced contractor. 

Western and Central Massachusetts were hit with tornadoes and strong thunderstorms yesterday, Protect Your Doors Against Wind creating significant damage to homes and property. Damage from a tornado is considered wind damage, and is covered by standard home insurance. 

The Division of Insurance has activated its consumer hotline number, Protect Your Doors Against Wind to handle any calls from homeowners seeking assistance.

Smoke Damage Restoration For Electronics

In Figure 17, the dashed vertical line represents the typical DC leakage current limit for a 150µF, 6.3V device while the solid vertical line represents the limit for a tantalum polymer device. It's clear that one of these capacitors would not have met the MnO2 limit and Electronic Restoration Smoke Damage Restoration For Electronics several ot  read more..

Water Damage

In the case of a severe storm like a tornado or hurricane, the relentless pounding of the wind can cause Emergency Board up Water Damage sometimes allowing the water to come in, through either a broken window, a splintered door or maybe some roof damage. Being proactive and planning ahead by the use of installing plywo  read more..

Some Safety Measures To Take Before During And After A Hurricane

If Evacuation Is Necessary If officials order evacuation, leave as soon as possible. Avoid flooded roads and watch for washed-out bridges.Secure your home. Unplug appliances and turn off electricity and the main water valve. If time permits, Emergency Board up Some Safety Measures To Take Before During And After A Hurricane elevate furniture to protect it from floodi  read more..

How To Remove Smoke Odor

Identification and Preparation of Cleaner Air Shelters for Protection of the Public from Wildfire Smoke 1. Identify one or more facilities with tight-sealing windows and doors and public access (for example, public schools, fire stations, or hospitals). As a rule of thumb, Smoke Damage How To Remove Smoke Odor newer build  read more..

Mold Mitigation Remediation

Testing is usually done to compare the levels and types of mold spores found inside the building with those found outside of the building or for comparison with another location in the building. In addition, Mold Remediation Mold Mitigation Remediation air sampling may provide tangible evidence supporting a hypothesis that inves  read more..

Animal Damage

Skunks are very well-known, nocturnal residents of most of the country. The common striped skunk, is characterized by prominent, lateral white stripes that run all the way down its back. Otherwise, the skunk’s fur is jet black, the body of the adult striped skunk is about the same size o  read more..

How To Confront Hoarders Regarding Their Problem

Accidentally losing important things like money, bills, prescriptions, and other significant documents within the clutter Difficult time turning down free items, even if they are not needed (like advertisements handed out on the sidewalk or mailed to the home) Persistently shops sales items to "stoc  read more..

Flood Damage Restoration For Electronics

The second observation is that the first breakdown for the tantalum polymer capacitors occurs at 1.75 times rated voltage. This is roughly twice as high as the lowest voltage seen for the MnO2-based capacitors.While the precise numerical value of this advantage varies somewhat with manufacturer and   read more..

Mold Abatement Regulations

This article presents remediation guidelines for building materials that have or are likely to have mold growth. The guidelines are designed to protect the health of cleanup personnel and other workers during remediation. These guidelines are based on the size of the area impacted by mold contaminat  read more..

Black Mold Caused By A Sewer Backup

The Community Folk Art Center, 805 E. Genesee St., will remain closed this week as officials continue to clean up. Water leaked through the ceiling and the sewer backed up, said Kevin Leonardi, its marketing specialist. Staff members quickly moved art and equipment to safety, but repairs were needed  read more..