Structural Drying >> Storm Damage

Woods are a byproduct of nature showing many inconsistencies. Cross-sectional (transverse) shrinkage isn’t always uniform. The quantity of shrinkage happening parallel with progress rings (tangential directions) ranges from one and one-half to two times as much as across, or at ninety degree angles to, the progress rings (radial directions) This difference in 6 directional shrinkages often causes warping in shape (cupping, diamonding and rectangular shapes from squares).

  1. A flat grain plank would shrink more in girth than a vertical grain plank of the same initial sizes. A flat grain plank from near the middle of a log would cup more than one sawn farther out from the middle. To further exacerbate these Storm Damage matters, the quantity of tangential and radial shrinkages (in per cent of greener dimensions per inch of dimensions), varied with the density of wood; i.e. values recorded for western larches and Douglas-firs are higher than that for redwoods, western red cedars and the western pines while they are lower than that for oak, hard maples and hickories when all are dried to the same humidity substance.
  2. Due to density variations within certain trees and between the trees (indicated by per cent summerwoods), actual shrinkages developing often would vary broadly from recorded values for these species. Published shrinkages values given for a species are average; it would be helpful if information included the variation in shrinkages to be expected during Storm Damage. Heavy shrinking allowed when sawing lumber to make up for variation in density and grain point results to a loss of footage. On the other hand, insufficient allowances result in a complete degradation from failure to surface out to standard sizes. Learning anything about variations odd to the timber sawn by a mill ought to be a valuable aid in reducing those losses, where practical.
  3. Not all of the portions of a plank reach the fibrous saturation point at the same time. The outer surfaces of a plank dry first and have the tendency to shrink, like change in humidity substance, progresses from the outside towards the middle of a plank (between opposite faces). Those results in the familiar development of Storm Damage stresses within a plank to cause case hardening, splits, checks, honeycombing and one form of collapses. Case hardening of lumber would result in very low total shrinkage values while collapses would result in significantly high values.
  4. Severity of stresses developed might be connected with the density of the wood in correlation to the conditions of humidity removal through the structural drying operation. Adjusting conditions to lumber traits is essential for Storm Damage; the same applies to segregation of lumber into groups with similar characteristics prior to Storm Damage. Undesirable vertical shrinkage often happens in many different types of lumber to cause twisting, crooking, bowing and cross breaks. Twisting happens where the vertical cells significantly vary in deviation from the axis of a plank (such as spirals, wavy and diagonal grains).

Water Extraction From Carpet After Pipe Breaks

In addition to the decline in land-surface altitude,the loss of marshes and barrier islands that dampen storm surge and waves during hurricanes increases the risks of flood disaster in New Orleans Water Extraction Water Extraction From Carpet After Pipe Breaks and vicinity.

Since 1940, approximately 1 million acres of c  read more..

How To Do Black Mold Removal

Mildew and molds are fungi - simple microscopic organisms that thrive anywhere there is a moist environment. Molds are a necessary part of the environment; without them, leaves would not decay and aspects of soil enrichment could not take place. It is their ability to destroy organic materials, howe  read more..

What Is The Best Way To Dry Out Carpets After A Ba

Extruded polystyrene, expanded polystyrene, and rigid mineral wool panels are routinely used in below-grade exterior foundation insulation systems. Extruded polystyrene has  read more..

OSHA Asbestos Abatement

The occupational safety and health administration has regulations concerning the health and safety of everyone in the workplace. This federal agency regulates the standards for any industry that works with Asbestos Abatement OSHA Asbestos Abatement or that manufactures anything made of asbestos such as the shipping industry and s  read more..

The Effects Meth Labs Have On Wildlife And Vegetat

In addition to the General Cleanup Requirements in Section B, at aminimum a typical cleanup for a Tier 2 Response shall Meth Lab Cleanup The Effects Meth Labs Have On Wildlife And Vegetat include the following:1) Where applicable/appropriate, follow all cleaning procedures described in Tier 1.2) This Tier differs from Tier 1 Responses in that additional af  read more..

How To Repair Smoke Damage From Fire

For the second time this month, Fire Damage How To Repair Smoke Damage From Fire another state joined the national movement to enhance public safety by mandating that all cigarettes sold in their state be "fire-safe.” Such cigarettes are less likely to ignite fires if dropped or carelessly discarded.

Tod  read more..

Asbestos Removal Courses In Wisconsin

"Category II nonfriable" is defined as "any material, excluding category I nonfriable, containing ... asbestos ... that ... cannot be crumbled ... to powder by hand pressure." This includes rigid exterior siding and boards by the trade name "transite". Category II Asbestos Abatement Asbestos Removal Courses In Wisconsin may not   read more..

How To Use A Tarp To Repair A Roof

Hurricane Rita 2005 Rita, the third Category 5 hurricane of the season, was a destructive and deadly hurricane that devastated portions of southeastern Texas and southwestern Louisiana and significantly impacted the Florida Keys.A tropical wave and the remnants of an old front combined to produ  read more..

California Asbestos Tile Removal Requirements

Identifying hazardous materials before starting work on a project site protects worker health and safety, building occupants, and the financial viability of the project. Doing this up front can help you choose the appropriate inspectors, consultants and contractors and avoid costly change orders or  read more..

Protect Your Doors Against Wind

Certain parts of the country have building codes requiring garage doors to withstand high winds. You should check with your local government building officials to see if there are code requirements for garage doors in your area. Some garage doors can be Wind Damage Protect Your Doors Against Wind strengthened with retrofit  read more..