Odor Control >> Wind Damage And Emergency Board Up

Plywood shutters that you create yourself, if placed correctly, could provide a high degree of Wind Damage And Emergency Board Up coverage from flying debris during a storm. Plywood shutters could be placed on all kinds of houses. Measure every window and every door that has glass, and add 8 inches to all the height and width to provide a 4-inch overhang on every side of the window or door. Pieces of plywood are generally 48 inches by 96 inches (4 x 8 feet).

  1. Inform your local hardware supply store the dimensions and amount of openings you require to cover the Wind Damage And Emergency Board Up to decide how many pieces of plywood to buy. To place plywood shutters, you may require bolts, wood or brick anchors, big washers, and 5/8-inch exterior-grade plywood. For windows 36 × 48 inches or littler placed on a wood framed house, utilize 1/4-inch lag bolts and plastic-coated durable anchors. The lag bolts shall intrude the wall and framed area the window at minimum 1-3/4 inches. For bigger windows, utilize 3/8-inch lag bolts that intrude the wall and framed area the window at minimum 2-1/2 inches. For windows 36 × 48 inches or littler placed on a brick house, utilize 1/4-inch expansion bolts and galvanized durable 2 inch expanding anchors.
  2. The expansion bolt shall intrude the wall at minimum 1-1/2 inches. For bigger windows, utilize 3/8-inch expansion bolts that intrude the wall at minimum 1-1/2 inches. The items you may require are a circular or hand saw, a bore with the accurately dimensioned bits, a mallet, and a spanner to fit the bolts. To be secure, utilize eye coverage and work gloves. Saw the plywood to the measurements for every opening. Bore holes 2-1/2 inches from the outside edge of the plywood at every corner and at 12-inch intervals. Bore four holes in the center area of the plywood to relieve pressure during a strong Wind Damage And Emergency Board Up storm.
  3. Place the Wind Damage And Emergency Board Up plywood over the opening, and mark every hole position on the outside wall. Bore holes with the appropriate dimensions and type of bit for the anchors. Place the anchors, the plywood, and the bolts to create sure they fit correctly. On wood-framed houses, create sure that the anchors are secured into the solid wood that framed the door or window and not into the siding or trim. Mark every shutter so you may know where it is to be placed, and store the shutters and the bolts in an accessible place.
  4. If the opening is bigger than one sheet of plywood, you may require you to create shutters with 24 × 48 bracing. This bracing could be two 24 × 48s at the middle and bottom of the two pieces of plywood, evenly spaced, with the 2-inch side attached to the inside of the Wind Damage And Emergency Board Up storm shutter. Attach the 24 × 48s to the outside of the Wind Damage And Emergency Board Up storm shutter with 2-inch, 10-gauge wood screws before placing the shutter. Impact-resistant windows are optimal for windows not easily fitted with hurricane shutters or those that are hard to reach.

Professional Water Damage Carpet Cleaning

In the wake of Hurricane Isaac's recent recovery efforts, Louisiana's restoration from Hurricane Rita persists, enabled by approximately$1.3 billion in Federal Emergency Management Agency public assistance, hazard mitigation Water Extraction Professional Water Damage Carpet Cleaning and individual assistance funding since her landfall on Sept  read more..

How To Clean Up Attic Mold

How do you get the molds out of buildings, including homes, schools, and places of employment?In most cases mold can be removed from hard surfaces by a thorough cleaning with commercial products, soap and water, or a bleach solution of no more than 1 cup of bleach in 1 gallon of water. Absorbent or   read more..

How To Troubleshoot Sensors On Circuit Boards

Solid-electrolyte tantalum capacitors were first developed and commercially produced in the 1950s. They represented a quantum leap forward in miniaturization and reliability over existing wound-foil wet electrolytic capacitors. While the solid tantalum capacitor has dramatically improved electrical   read more..

Water Extraction

By conditioning our crawl spaces this may make them perform better than just a vented crawl space in the terms of safety, health, comfort, durability and energy consumption. When we condition our crawl spaces, they do not cost more to build than a vented Crawl Space Drying Water Extraction. Your existing vented crawl spaces  read more..

Radon Maps

Biological Air Pollutants Provide adequate outdoor air ventilation. Keep equipment water reservoirs clean. Eliminate standing water, wash bedding and soft toys frequently in hot water. Vacuum carpets and upholstered furniture regularly. Read more at www.epa.gov/iaq/biologic.html Volatile O  read more..

Tunneling animals

You want to have the nicest lawn in the neighborhood, you want people to think that Arnold Palmer lives here. The last thing you want is some kind of animal damage, some animal rooting around in your garden or tearing up your grass. You think,” how can I stop this”, but first you s  read more..

Ceiling Leak Covered By Home Insurance

Advisory Base Flood Elevations The Katrina Recovery Maps (see Figure 1) include the following information: Pre-Katrina aerial photographs (as a base map) Approximate Katrina surge inundation limit (shaded area) ABFE contours (ft NGVD) Predicted inland limit Structural Drying Ceiling Leak Covered By Home Insurance of damaging wave effects du  read more..

How To Refurbish An Apartment After Tenants Trash

When a landlord and tenant get along well, things are better all around. Dealing with unhappy tenants is alot of trouble for a landlord, and few tenants want the inconvenience and expense of moving simplybecause they cannot get along with their landlords.Yet, Tenant Move Out Cleanup How To Refurbish An Apartment After Tenants Trash landlords and tenants fre  read more..

What Is Radon

What is what is radon? What is radon is a radioactive gas released from the normal decay of the elements uranium, thorium, and radium in rocks and soil. It is an invisible, odorless, tasteless gas that seeps up through the ground and diffuses into the air. In a few areas, depending on local geology,  read more..

General Mold Cleanup Procedures

General Mold Cleanup Procedures Identify and correct the moisture source Clean, disinfect, and dry the moldy area Bag and dispose any material that has moldy residues, such as rags, paper, leaves, or debris What can I save? What should I toss? Substances that are porous and can trap molds, such as p  read more..