Mold Remediation >> Safe Ways To Remove Mold

Mold Health Risks Molds are small organisms found almost everywhere, inside and outside, including on plants, foods and dry leaves. Molds are beneficial to the environment and are needed to break down dead material. Very tiny and lightweight, mold spores travel easily through the air. When molds are present in large numbers, Safe Ways To Remove Mold they may cause allergic symptoms similar to those caused by plant pollen.

Exposure to a large number of mold spores may cause allergic symptoms such as watery eyes, runny nose, sneezing, itching, coughing, wheezing, difficulty breathing, headache, and fatigue. Repeated exposure to mold can increase a person’s sensitivity, Safe Ways To Remove Mold causing more severe allergic reactions. These problems are worse indoors, where mold causes indoor air quality problems. 

Certain molds, such as Stachybotrys and Aspergillus,can produce toxins called mycotoxins under certain conditions. Exposure to mycotoxins can cause more serious illness. Populations at Risk People who live or work in buildings that are exposed to moisture Safe Ways To Remove Mold and not adequately ventilated are more at risk of illnesses causes by mold. 

Populations at particular risk include: infants and children, elderly persons, immune compromised patients Safe Ways To Remove Mold and people with existing respiratory conditions, such as allergies and asthma.What you should do Check for Mold Testing for molds is very difficult and expensive and cannot determine whether health effects will occur. 

Mold is normally found outdoors and counts fluctuate from day to day depending on the season. Due to the uncertainties associated with testing for molds, it is not recommended in most cases. If you can see or smell mold it needs to be cleaned up.Sources of moisture in your home may include; flooding, damp basement or crawl space, leaky roof, leaky plumbing, humidifiers, poorly ventilated areas, Safe Ways To Remove Mold and/or clothes dryer vented indoors.

Prevent Mold from Growing Back Use dehumidifiers in damp areas, such as the basement Fix leaks in the roof, walls, windows, or pipes Ventilate bathrooms, kitchens, Safe Ways To Remove Mold and laundry areas Vent clothes dryer to the outside Use mold-resistant paint Dry areas that are wet or have been flooded within 24 to 48 hours, throw out anything that cannot be completely dried 

Remove Mold If you can see or smell mold, Safe Ways To Remove Mold it is present and must be cleaned up. You also need to fix the problem causing the mold to prevent it from growing again.It is important to make sure that sources of moisture are eliminated before mold is cleaned up. If this is not done, the mold will grow again. 

If an area of mold growth is larger than 10 square feet (3 feet x 3 feet), Safe Ways To Remove Mold it is recommended that a contractor with experience in mold remediation clean up the area. If the area is less than 10 square feet, in most cases you can do the job yourself.important to take precautions to LIMIT YOUR EXPOSURE to mold and mold spores. 

Cleaning while wearing N-95 respiratory, gloves and goggles Cleaning while wearing N-95 respirator, gloves and goggles. Click on the image for a larger version. Avoid breathing in mold or mold spores. In order to limit your exposure to airborne mold, Safe Ways To Remove Mold you may want to wear an N-95 respirator, available at many hardware stores and from companies that advertise on the Internet. (They cost about $12 to $25.) 

Some N-95 respirators resemble a paper dust mask with a nozzle on the front, others are made primarily of plastic Safe Ways To Remove Mold or rubber and have removable cartridges that trap most of the mold spores from entering. In order to be effective, the respirator or mask must fit properly, so carefully follow the instructions supplied with the respirator. 

Please note that the Occupational Safety and Health Administration (OSHA) requires that respirators fit properly (fit testing) when used in an occupational setting; consult OSHA for more information (800-321-OSHA or Safe Ways To Remove Mold www.osha.gov).Wear gloves. Long gloves that extend to the middle of the forearm are recommended. 

When working with water and a mild detergent, ordinary household rubber gloves may be used. If you are using a disinfectant, a biocide such as chlorine bleach, or a strong cleaning solution, Safe Ways To Remove Mold you should select gloves made from natural rubber, neoprene, nitrile, polyurethane, or PVC (see Cleanup and Biocides). Avoid touching mold or moldy items with your bare hands.

Wear goggles. Goggles that do not have ventilation holes are recommended. Avoid getting mold Safe Ways To Remove Mold or mold spores in your eyes. How Do I Know When the Remediation or Cleanup is Finished? http://www.epa.gov/mold/images/suitcase_sm.jpg Mold growing on a suitcase stored in a humid basement. 

Click on the image for a larger version.You must have completely fixed the water or moisture problem before the cleanup or Safe Ways To Remove Mold remediation can be considered finished.You should have completed mold removal. Visible mold and moldy odors should not be present. Please note that mold may cause staining and cosmetic damage.

You should have revisited the site(s) shortly after cleanup and it should show no signs of water damage or mold growth.People should have been able to occupy or Safe Ways To Remove Mold re-occupy the area without health complaints or physical symptoms.Ultimately, this is a judgment call; there is no easy answer. If you have concerns or questions consult our Frequently Asked Questions database and ask a question if you don't find what you need.

Moisture and Mold Prevention and Control Tips Moisture Control is the Key to Mold Control Mold growing on the Safe Ways To Remove Mold surface of a unit ventilator. Mold growing on the surface of a unit ventilator. Click on the image for a larger version. http://www.epa.gov/mold/images/condensation.jpg Condensation on the inside of a windowpane.

When water leaks or spills occur indoors - ACT QUICKLY. If wet or damp materials or areas are dried 24-48 hours after a leak or spill happens, Safe Ways To Remove Mold in most cases mold will not grow. Clean and repair roof gutters regularly. Make sure the ground slopes away from the building foundation, so that water does not enter or collect around the foundation.

Keep air conditioning drip pans clean and the drain lines unobstructed and flowing properly. Keep indoor humidity low. If possible, Safe Ways To Remove Mold keep indoor humidity below 60 percent (ideally between 30 and 50 percent) relative humidity. Relative humidity can be measured with a moisture or humidity meter, a small, inexpensive ($10-$50) instrument available at many hardware stores. 

If you see condensation or moisture collecting on windows, walls Safe Ways To Remove Mold or pipes ACT QUICKLY to dry the wet surface and reduce the moisture/water source. Condensation can be a sign of high humidity.Actions that will help to reduce humidity Vent appliances that produce moisture, such as clothes dryers, stoves, and kerosene heaters to the outside where possible. 

(Combustion appliances such as stoves and kerosene heaters produce water vapor and will increase the humidity unless vented to the outside.)Use air conditioners Safe Ways To Remove Mold and/or de-humidifiers when needed.Run the bathroom fan or open the window when showering. Use exhaust fans or open windows whenever cooking, running the dishwasher or dishwashing, etc. 

Actions that will help prevent condensation. Mold growing on a wooden headboard in a room with high humidity. Click on the image for a larger version. Reduce the humidity. Increase ventilation or air movement by opening doors and/or windows, Safe Ways To Remove Mold when practical. Use fans as needed.Cover cold surfaces, such as cold water pipes, with insulation.Increase air temperature.

Renters: Report all plumbing leaks and moisture problems immediately to your building owner, manager, or superintendent. In cases where persistent water problems are not addressed, Safe Ways To Remove Mold you may want to contact local, state, or federal health or housing authorities. You can also contact your state health department.

Testing or Sampling for Mold Rust is an indicator that condensation occurs on this drainpipe. The pipe should be insulated to prevent condensation. Click on the image for a larger version.Is sampling for mold needed? In most cases, if visible mold growth is present, sampling is unnecessary. Since no EPA or Safe Ways To Remove Mold other federal limits have been set for mold or mold spores, sampling cannot be used to check a building's compliance with federal mold standards. 

Surface sampling may be useful to determine if an area has been adequately cleaned Safe Ways To Remove Mold or remediated. Sampling for mold should be conducted by professionals who have specific experience in designing mold sampling protocols, sampling methods, and interpreting results. 

Sample analysis Safe Ways To Remove Mold should follow analytical methods recommended by the American Industrial Hygiene Association (AIHA), the American Conference of Governmental Industrial Hygienists (ACGIH), or other professional organizations.

Vermiculite Insulation

Protect Your Family from Asbestos Abatement Vermiculite Insulation Asbestos-Contaminated Vermiculite insulation Insulation This page provides important information on how to protect yourself and your family i  read more..

How To Paint Over Fire Damage On Drywall

The president of NFPA (National Fire Protection Association) today called for all nursing homes in the U.S. to be equipped with fire sprinklers, in the wake of two recent nursing home fires in Hartford and Nashville, Fire Damage How To Paint Over Fire Damage On Drywall where a total of 24 people died. (See NFPA's fact sheet on nursing home fire s  read more..

Bird And Animal Damage To Lawns

This free permit is given to control a nuisance wild animal protected by state law. Those who provide a service to the public or charge a fee for nuisance wild animal control services must pass a test before obtaining a permit. Migratory birds, including Canada geese and woodpeckers, are federally p  read more..

Asbestos Exposure

What is asbestos exposure? Asbestos exposure is the name given to a group of minerals that occur naturally in the environment as bundles of fibers that can be separated into thin, durable threads. These fibers are resistant to heat, fire, and chemicals and do not conduct electricity. For these reaso  read more..

Snake Removal in Garden

Most people like to have a nice garden the more plan to have, the better, but having a lush garden could also invite Animal Damage Snake Removal in Garden. I'm not sure if you know this but most snakes are not dangerous and most certainly do not want a confrontation with a human. Even the venomous snakes will not attack un  read more..

Crime Scene Technician Certification

In 2008, Karen Evans, administrator of the Office of Government and Information Technology at the White House's Office of Management and Budget (OMB), wrote a memo to all government chief information officers that read, Crime Scene Cleanup Crime Scene Technician Certification in part: 

"The Government's reli  read more..

Asbestos Abatement Jobs


  read more..

Some Safety Measures To Take Before During And After A Hurricane

If Evacuation Is Necessary If officials order evacuation, leave as soon as possible. Avoid flooded roads and watch for washed-out bridges.Secure your home. Unplug appliances and turn off electricity and the main water valve. If time permits, Emergency Board up Some Safety Measures To Take Before During And After A Hurricane elevate furniture to protect it from floodi  read more..

How To Keep Animals Out Of AC Duct Work

Executive Order 12342, January 24, 1982, permits the use of chemical toxicants registered by the Environmental Protection Agency for predator damage control on federal lands. 3. Department of Agriculture Regulation (DR) 9500-4 (2601.2) requires Department of Agriculture programs to include measures   read more..

Types Of Security For Fenced Yards

Storm surge levels on Galveston Island and on the west side of Galveston Bay are estimated to be between 10 and 15 ft. Here, too, several NOS tide gauges failed, although the gauge at Eagle Point on the west side of Galveston Bay recorded a maximum surge of 11.48 ft.The highest inundation, of at lea  read more..