Lead Paint Removal >> Lead Paint Removal Regulations

What surfaces are not suitable for encapsulation? "Friction" and high profile (i.e., protruding window sills) surfaces are not suitable, regardless of their condition.Friction surfaces include: window jambs; glides; headers; some stops and parting beads; inside, close-fitting door jambs and stops; floors; stair treads; and Lead Paint Removal Regulations thresholds. 

Cabinets with friction surfaces, such as drawers and cabinet doors, should be examined before encapsulation. Where friction exists, Lead Paint Removal Regulations planing of the surfaces is recommended. What are the advantages of using encapsulants? Residents may not need to leave the building during surface preparation and application if no dust is released.

Occupants should never be in the immediate work area (i.e., same room) during application. If a surface with lead paint is intact,it may be possible to apply an encapsulant without surface preparation. Use of encapsulants may be less costly, Lead Paint Removal Regulations more time saving, and safer than other methods.What are the disadvantages of using encapsulants? 

There is limited experience or information on long-term performance of encapsulants. Encapsulants cannot be used on surfaces that experience abrasion or constant friction. Encapsulants may prematurely wear on a surface that experiences repeated impact, Lead Paint Removal Regulations such as door stops, window stops and stair treads. 

Encapsulants may peel off improperly prepared surfaces that have old undercoats of paint. It is essential to test an encapsulant on-site before applying. Encapsulants require periodic inspection for repair or Lead Paint Removal Regulations maintenance. Water from roof leaks or broken pipes may damage encapsulants. Encapsulants must be applied when the air temperature and relative humidity are within specified ranges. 

Lead-based paint is a health hazard to children and adults, because the dust chips and fumes can be ingested or inhaled. In 1978, Lead Paint Removal Regulations the U.S. Consumer Product Safety Commission limited the amount of lead allowed in paint. Any surface painted before that year has the potential to be a lead hazard. Lead paint hazards can be controlled in several ways: 

Doors and windows containing lead paint can be replaced, paint can be removed utilizing a method that minimizes dust and fumes, or surfaces can be covered with hard materials, Lead Paint Removal Regulations such as sheet rock or paneling. The use of encapsulants is also available as a technique to prevent exposure to lead-based paint. 

The instructions and guidance of the manufacturers must be followed to test, prepare and apply these products. What are encapsulants? Encapsulants are materials that are applied over lead-based paint to seal the paint to a surface and prevent the release of paint chips or dust.The material may be either a liquid or Lead Paint Removal Regulations an adhesive. 

Encapsulation provides a barrier between the paint and the environment. Conventional paint is NOT an encapsulant. How do encapsulants work? Encapsulants cover lead paint so that the paint cannot produce dangerous dust, and Lead Paint Removal Regulations humans cannot come into contact with it. Encapsulants work best on clean, dry and solid surfaces. 

Encapsulants cannot be used on: – Surfaces which are walked on;– Surfaces which rub together;– Surfaces which are badly deteriorated. Are encapsulants all the same? There are three types of encapsulants: There are polymers (chemical compounds) that form a flexible,resilient membrane.
They are applied with a brush, roller, or Lead Paint Removal Regulations airless spray gun. 

There are epoxy or polyurethane polymers that form a membrane with a hard, but flexible, Lead Paint Removal Regulations surface. They are applied with a brush,roller, or airless spray gun. There are cement-like materials with polymers which cure to form a thick coating. They are generally applied with a trowel. How do I decide to use an encapsulant?

There are several points to consider before using an encapsulant: You must follow the manufacturer's guidelines for testing, preparation Lead Paint Removal Regulations and application. The person performing the on-site testing to determine appropriate surfaces for encapsulants must meet standards set by the manufacturer. Although encapsulants offer permanent protection from lead based paint, they must be periodically inspected and repaired, if damaged. 

You must use different encapsulants indifferent situations. Follow the manufacturers' recommendations and Lead Paint Removal Regulations instructions. Encapsulation, or any other measures used to control conditions related to lead poisoning, must have prior approval by the state or local department of health. When covering lead paint, some thicker encapsulants may also destroy architectural detail, especially on moldings. 

Encapsulants must be applied by a person who has met the manufacturers' specifications. Contact the manufacturer for specific criteria. The only permanent solutions which do not require periodic maintenance and inspection include replacement of doors and windows, or Lead Paint Removal Regulations complete removal of lead paint. 

How do I find out which encapsulants are acceptable for use in New York State? Call your local health department or Lead Paint Removal Regulations the state Department of Health's Residential Lead Hazard Control Unit at 1-800-458-1158. The state Health Department issues an "Acceptable Encapsulant Product List." Consult the list for encapsulant product names. 

Products on this list meet the safety and performance standards of the American Society for Testing and Materials Standard.What surfaces are suitable for encapsulation? The surfaces should be: Dry and free of grime, dirt, dust,grease, charring, Lead Paint Removal Regulations smoke residue(especially cigarette or hydrocarbon), mildew, or other contaminants.

Water-based encapsulants will tolerate damp, but not wet, surfaces without losing their most important properties. Free of water leaks. Non-glossy. High gloss surfaces can be deglossed with chemical deglossers or Lead Paint Removal Regulations wet sanding before encapsulation. In architecturally sound condition. Undamaged (i.e., no holes or large cracks in walls). 

Damaged areas must be repaired prior to encapsulation. What are the symptoms of lead poisoning? Small amounts of lead can build up in the body and cause temporary symptoms or permanent damage.Early signs of lead poisoning may include tiredness, headache, metallic taste and poor appetite. Advanced lead poisoning symptoms include mood swings, sleeping problems, stomach cramping, constipation, memory loss, a tingling sensation in the extremities and Lead Paint Removal Regulations muscle and joint aches.

How can I be exposed to lead? Lead commonly enters the body in two ways. Lead can be ingested (swallowed) when drinking, eating, smoking, chewing gum, applying cosmetics or Lead Paint Removal Regulations performing other hand to mouth activities.It can be inhaled by breathing in lead dust or fumes.

At the construction site, old paint on metal bridges and Lead Paint Removal Regulations other steel structures may contain lead. Lead poisoning has occurred in workers during abrasive blasting, sanding, cutting, burning, or welding of bridges and other steel structures coated with lead-containing paints. Anyone near such work can be exposed to lead.

Mold Remediation

A lack of clear level reliance between levels 1 and 3 suggests that this piece of the tolerance purpose might reflect merely "noise-level" displeasure that would happen if Odor Control Mold Remediation level ever surpassed the threshold. Butanol equaling purposes gotten with aeration rates of 2.5 and 5/s"' per resident,   read more..

Mold Sickness

Flood conditions contribute to the growth and transmission of many kinds of fungi, some of which can cause sickness. Cleanup workers are at increased risk of exposure to airborne fungi and their spores because they often handle moldy building materials, decaying vegetable matter, rotting waste mater  read more..

How To Remove A Moldy Smell From A Crawl Space


In an unconditioned basement, you must: Insulate the floor above the basement. The required R-value depends on the results of your compliance analysis. Insulate the stairwell between the basement and conditioned first floor. Insulate heating pipes and air ducts in the basement.&n  read more..

The Typical Cost Of Tree Removal

Tornado Debris: Damage from tornadoes is caused by high-velocity rotating winds. The severity of the damage depends on the size of the tornado funnel and the length of time the funnel touches the ground. Damage is generally confined to a narrow path extending up to half a mile wide and Debris Removal The Typical Cost Of Tree Removal&nbs  read more..

Roof Damage Insurance Claim Tips

Roofing systems commonly rely on roof sheathing and bottom chords to provide lateral support for the roof trusses. Oliver and Hanson (1994) and Riba et al. (1994), agree that roofing systems could be considerably improved if simple secondary bracing were installed between Wind Damage Roof Damage Insurance Claim Tips trusses.&nbs  read more..

Frozen Pipe Cost

Household Plumbing TipsThe City of Phoenix Water Services Department has almost 7,000 miles of water mains throughout the city.Phoenix Water Services is responsible for repairing all leaks, broken pipes, and water mains on the city, or Water Damage Frozen Pipe Cost street side of the water meters. 

  read more..

How To Get A House Tested For Mold

Preventing mold and bacterial growth in the building's ventilation system Ventilation systems should be checked regularly, particularly for damp filters and overall cleanliness (1). A preventive maintenance plan should be put into place for each major component of the building's ventilation system.   read more..

Roof Leak Diverter

Focus on high value items that were not water impacted and items that have special significance. If an entire item cannot be saved, consider parts that could be saved. For example, if a family heirloom such as an antique chest cannot be saved, consider saving the non-porous handles Structural Drying Roof Leak Diverter or  read more..

Structural Drying

Convalescent heat substitute is a worldwide skill appropriate to vapor-density, direct-growth, and cooled-water air-handling-unit (AHU) coils; heat-driven desiccant Dehumidification Structural Drying equipment; dehumidifiers; supermarket, ice-rink, and natatorium air-conditioning and dehumidification systems; and bundled   read more..

Lead Paint Removal Certification

Ether enzyme, ferrochelatase, is also inhibited at low blood lead levels. Inhibition of ferrochelatase leads to increase free erythrocyte protoporphyrin (FEP) in the blood which can then bind to zinc to yield zinc protoporphyrin (ZPP). At a blood lead level of 50 µg/100 g or greater, nearly 100%   read more..