Document restoration >> Mold Remediation

The following are the minimum steps that shall be applied to all Mold Remediation projects, and for smaller, minor restorations that could be in non-sensitive, unoccupied areas such as the flooded regions that have involved personal, single dwelling homes. This information will help you understand how a professional water restoration company would handle a thorough and complete water damage project. These are the steps that we take.

  1. Locate and eliminate the source of water or excessive moisture that is causing the Mold Remediation. Re-confirm that the water source has been eliminated and the mold has been minimized where the documents have been stored as well as possible before proceeding. If document items in the room could become contaminated with black mold spores or construction debris, remove every room item from the mold remediation area, such as water damaged computer equipment and upholstered furniture or protect with plastic. All building and other materials that could not be entirely dried out in a 48 hour period shall be removed from the vicinity and disposed of except some “hard” materials and furnishing could be evaluated for salvage.
  2. Clean the work vicinity and surrounding surfaces, use a HEPA vacuum on the Mold Remediation where possible. Non-porous materials such as metals, glass, and hard plastics and semi-porous to non-porous materials like wood, and concrete materials that might be structurally sound and could be potentially or visibly moldy might be cleaned and reused. Use a mild cleansing solution, and rinse well and dry off, the surfaces should also be cleaned/disinfected with the administration approved cleaner, such as Virex II or similar mild cleaning mixture.
  3. In almost all cases, bleach shall not be used as it can damage the documents or pit metallic and any other hard surfaces, and will require excessive contact time to work effectively on Mold Remediation, and can produce strong toxic odors. Building materials like wallboard, drywall, ceiling tiles, wallpaper, and other cellulose-based materials that could become wet and might remain moist for more than 48 hours shall be discarded and replaced.  This Mold Remediation guideline will also apply to materials that could house mold spores but that will not be cleaned, such as damaged and contaminated cellulose and fiberglass insulation and insulation pipe wrap.
  4. Carpet that remains damp or wet for more than 48 hours, or that could become repeatedly wet due to re-occurring water intrusion events, shall be evaluated for possible removal and disposed.  If the area is below-grade, like in the basement work area, carpet shall not be reinstalled especially if the area is susceptible to recurrent water-intrusion or a constant high relative humidity levels that are greater than 60%. The use of dust suppression methods on materials that will be cut out, such as moistened surfaces prior to cutting, do not soak or saturate the Mold Remediation. Remove mold or water-damaged document materials in sealed bags or sealed containers. Try to leave the document processing area dry and clean.

Cleaning Mold On Foundation Walls In A Basement

Concern about indoor exposure to mold has increased along with public awareness that exposure to mold can cause a variety of health effects and symptoms, including allergic reactions. This safety and health information bulletin provides recommendations for the prevention of mold growth and describes  read more..

Samples Taken By Lead Paint Workers

Samples for dry manual sanding were taken at three different work sites; at each site, three samples were taken on an individual worker while he or she worked on one visually uniform paint surface. A distribution of potential full-shift exposures was modeled for work at each work site. It was assume  read more..

How Does Barometric Pressure Make Radon Levels Go

Please provide the telephone number where you or your organization's official contact person can be reached during business hours, Monday through Friday. If you have facsimile capabilities, please indicate a fax number where correspondence can be sent to you. Use only if the telephone number or fax   read more..

Recycling

Recycling Basics Recycling is the process of collecting and processing materials that would otherwise be thrown away as trash and turning them into new products. Debris Removal Recycling can benefit your community and the environment. Benefits of Recycling Reduces the amount of waste sent to landfills and incinerators.  read more..

How To Remove Fire Smoke Smell From Apartment

Proper selection of PPE for individual responders must be based upon a careful assessment of two factors: (1) the hazards anticipated to be present, or are present at the scene and (2) the probable impact of those hazards, based upon the mission role of the individual. The emergency responder must b  read more..

Asbestos Mitigation

Basically asbestos comes from a group of naturally occurring minerals, with fibers that are of a thin elongated mass which can be separated easily from its strands. These minerals have excellent insulating value, highly resistant to heat and chemicals with flexible fibers that can be woven ea  read more..

Coming Home To Flood Damage

Steps to File Your Flood Insurance Claim

Step 1. Contact your agent to report your loss: Have ready the name of your insurance company (your agent may write policies for more than one company), Flood Damage Coming Home To Flood Damage policy number and a phone number and/or e-mail address where you can be reached.
  read more..

Desiccant Vs Mechanical Dehumidification

System description and operation principle Various low-temperature desalination units have been constructed base on the principle of humidification-dehumidification. The basic principle of all these techniques is to convert salt water to humidified air and Dehumidification Desiccant Vs Mechanical Dehumidification then condense the water vapo  read more..

When Is Dehumidification Required?

The main cooling coil without being re-evaporated by radiant or conducted heat. The main cooling coil must be Dehumidification When Is Dehumidification Required? selected at a coil face velocity at least 150 fpm below the maximum cataloged face velocity to ensure that moisture does not carry over onto a reheat coil (liquid water carryover o  read more..

How To Clean Smoke Damage From Walls And Fixtures

The total amount of a given species released by a fire is thus dependent on the fuel consumed.This is most typically specified as a user input based on a combination of the burning object's heat release rate, mass loss rate, and heat of combustion (Hc) related as ܳ. The discussion above is ess  read more..