Asbestos Abatement >> Asbestos Removal Specifications In Tennessee

Counting Fibers (1) Place the prepared sample slide on the mechanical stage of the microscope. Position the center of the wedge under the objective lens and focus upon the sample. (2) Start counting from one end of the wedge and Asbestos Removal Specifications In Tennessee progress along a radial line to the other end (count in either direction from perimeter to wedge tip). 

Select fields randomly, without looking into the eyepieces, by slightly advancing the slide in one direction with the mechanical stage control. (3) Continually scan over a range of local planes (generally the upper 10 to 15 um of the filter surface) with the fine focus control during Asbestos Removal Specifications In Tennessee each field count. Spend at least 5 to 15 seconds per field. 

Most samples will contain asbestos fibers with fiber diameters less than 1 um. Look carefully for faint fiber images. The small diameter fibers will be very hard to see. However, Asbestos Removal Specifications In Tennessee they are an important contribution to the total count. (5) Count only fibers equal to or longer than 5 um. Measure the length of curved fibers along the curve. 

Count fibers which have a length to width ratio of 3:1 or greater. (7) Count all the fibers in at least 20 fields. Continue counting until either 100 fibers are counted or 100 fields have been viewed; whichever occurs first. Count all the fibers in the final field. (8) Fibers lying entirely within the boundary of the Walton-Beckett graticule field shall receive a count of Asbestos Removal Specifications In Tennessee.

Fibers crossing the boundary once, having one end within the circle shall receive a count of 1/2. Do not count any fiber that crosses the graticule boundary more than once. Reject and do not count any other fibers even though Asbestos Removal Specifications In Tennessee they may be visible outside the graticule area. If a fiber touches the circle, it is considered to cross the line. 

Count bundles of fibers as one fiber unless individual fibers can be clearly identified and each individual fiber is clearly not connected to another counted fiber. See Figure 1 for counting conventions. (10) Record the number of fibers in each field in a consistent way such that filter non-uniformity can be assessed. (11) Regularly check Asbestos Removal Specifications In Tennessee phase ring alignment. 

When an agglomerate (mass of material) covers more than 25% of the field of view, reject the field and select another. Do not include it in the number of fields counted. (13) Perform a "blind recount" of 1 in every 10 filter wedges (slides). Re-label the slides using a person other than the original Asbestos Removal Specifications In Tennessee counter. 6.7. Fiber Identification 

As previously mentioned in Section 1.3., PCM does not provide positive confirmation of asbestos fibers. Alternate differential counting techniques should be used if discrimination is desirable. Differential Asbestos Removal Specifications In Tennessee counting may include primary discrimination based on morphology.

Polarized light analysis of fibers, or modification of PCM data by Scanning Electron or Transmission Electron Microscopy. A great deal of experience is required to routinely and correctly perform differential counting. It is discouraged unless it is legally necessary. Then, only if a fiber is obviously not asbestos should it be excluded from the Asbestos Removal Specifications In Tennessee count. 

Further discussion of this technique can be found in reference 8.10. If there is a question whether a fiber is asbestos or not, follow the rule: "WHEN IN DOUBT, COUNT." 6.8. Analytical Asbestos Removal Specifications In Tennessee Recommendations -- Quality Control System 6.8.1. 

All individuals performing asbestos analysis must have taken the NIOSH course for sampling and evaluating airborne asbestos or an equivalent course. 6.8.2. Each laboratory engaged in asbestos counting shall set up a slide trading arrangement with at least two other laboratories in order to compare performance Asbestos Removal Specifications In Tennessee and eliminate inbreeding of error. 

The slide exchange occurs at least semiannually. The round robin results shall be posted where all analysts can view individual analyst's results. 6.8.3. Each laboratory engaged in asbestos counting shall participate in the Proficiency Analytical Testing Program, the Asbestos Analyst Registry or equivalent. 
Each analyst shall select Asbestos Removal Specifications In Tennessee and count prepared slides from a "slide bank". 

These are quality assurance counts. The slide bank shall be prepared using uniformly distributed samples taken from the workload. Fiber densities should cover the entire range routinely analyzed by the laboratory. These Asbestos Removal Specifications In Tennessee slides are counted blind by all counters to establish an original standard deviation. This historical distribution is compared with the quality assurance counts. 

A counter must have 95% of all quality control samples counted within three standard deviations of the historical mean. This count is then integrated into a new historical mean and standard deviation for the slide. The Asbestos Removal Specifications In Tennessee analyses done by the counters to establish the slide bank may be used for an interim quality control program if the data are treated in a proper statistical fashion.  

CALCULATIONS Calculate the estimated airborne asbestos fiber concentration on the filter sample using the following formula: Where: AC = Airborne fiber concentration (For Equation A, ) FB = Total number of fibers greater than 5 um counted FL = Total number of fields counted on the filter BFB = Total number of fibers greater than 5 um counted in the blank BFL = 

Total number of fields counted on the blank ECA = Effective collecting area of filter (385 mm(2) nominal for a 25-mm filter.) FR = Pump flow rate (L/min) MFA = Microscope count field area (mm(2)). This Asbestos Removal Specifications In Tennessee is 0.00785 mm(2) for a Walton-Beckett Graticule. 

T = Sample collection time (min) 1,000 = Conversion of L to cc Note: The collection area of a filter is seldom equal to 385 mm(2). It is appropriate for laboratories to routinely monitor the exact diameter using an inside micrometer. The collection area is calculated according to the Asbestos Removal Specifications In Tennessee formula: 

Short-cut Calculation Since a given analyst always has the same interpupillary distance, the number of fields per filter for a particular analyst will remain constant for a given size filter. The field size for that analyst is constant (i.e. the Asbestos Removal Specifications In Tennessee analyst is using an assigned microscope and is not changing the reticle). 

For example, if the exposed area of the filter is always 385 mm(2) and the size of the field is always 0.00785 mm(2), the number of fields per filter will always be 49,000. In addition it is necessary to convert liters of air to cc. 
These three constants can then be combined such that Asbestos Removal Specifications In Tennessee. 

The previous equation simplifies to: (For Equation B, ) 7.3. Recount Calculations As mentioned in step 13 of Section 6.6.2., a "blind recount" of 10% of the slides is performed. In all Asbestos Removal Specifications In Tennessee cases, differences will be observed between the first and second counts of the same filter wedge. 

Most of these differences will be due to chance alone, that is, due to the random variability (precision) of the count method. Statistical recount  criteria enables one to decide whether observed differences can be explained due to chance alone or are probably due to systematic differences between Asbestos Removal Specifications In Tennessee analysts, microscopes, or other biasing factors.

How To Restore Fire Damaged Electronics

The project shall minimize the usage of any commercial parts for all grade levels. There are no controls in commercial industry that are imposed uniformly upon all manufacturers to build in a common acceptable quality level. While many manufacturers maintain good quality controls, Electronic Restoration How To Restore Fire Damaged Electronics oth  read more..

Cleaning Up After A Fire

The number of fires caused by lighted tobacco products–almost always cigarettes–increased by a stunning 19 percent in the most recent year studied, Fire Damage Cleaning Up After A Fire according to research by the NFPA (National Fire Protection Association).

But laws requiring that cigarettes be desig  read more..

How To Remove Fire Damage From Furniture

Nineteen fire chiefs from around the world will participate in the National Fire Protection Association (NFPA) Urban Fire Forum in Boston, October 19-22. Also in attendance will be R. David Paulison. Fire Damage How To Remove Fire Damage From Furniture

Paulison is currently the Under Secretary of Federal Emergency Management/Direct  read more..

Carpet Water Damage

Can I save my Christmas or other holiday decorations?It depends on how quickly you can dry them out and how easy they are to clean. For example,tinsel and Water Extraction Carpet Water Damage paper items that were flooded should probably be discarded. Flood damaged electriclights should be discarded unless they were kept  read more..

Basement Drying

Unprotected building occupants and water restoration workers should be evacuated from the Sewage Cleanup Basement Drying affected areas during the beginning stages of decontamination, sewage cleaning, and disinfection, such as until the sewage has been completely removed and the disinfectants applied. The water restor  read more..

Lead Poisoning Questions And Answers

California has enacted landmark legislation to prevent childhood lead poisoning. This legislation has established the Childhood Lead Poisoning Prevention Branch (CLPPB), a children's environmental health program offering multi-layered solutions to this complex problem. What is lead poisoning? Lead   read more..

Structural Drying

There are many factors when dealing with the Sewage Cleanup Structural Drying remediation of the problem. Among these problems are the cause of the sewage contamination, the types of water-damaged materials in your building like are they organic or synthetic, are the surfaces porous, semi-porous, or nonporous, the sewag  read more..

Will Acrylic Primer Seal Lead Paint

The engineering controls and work practices associated with the employee's job assignment including training of employees to follow relevant good work practices described in Appendix B of this section; The contents of any compliance plan and Lead Paint Removal Will Acrylic Primer Seal Lead Paint the location of regulated areas in effect.   read more..

Grants For Ice Storm Tree Removal

Determine Management Options and Goals
Any disaster debris management plan should include a disposal strategy. Communities need to set priorities for recycling wastes and determine the desired disposal options for the remaining waste. Segregate Hazardous Waste - Be prepared to [M  read more..

Regulations For Meth Cleanup

Evaluation of other Potential ReleasesKDWM shall be contacted immediately if evidence of a release of a hazardous substance related to methlab activity is observed to the environment outside the Meth Lab Cleanup Regulations For Meth Cleanup inhabitable property, i.e., soil staining, spills,chemical containers with wastes or residues,   read more..