Asbestos Abatement >> How Do I Remove Asbestos Siding In North Carolina

A set of index of refraction oils from about n = 1.350 to n = 2.000 in n = 0.005 increments. (Standard for Becke line analysis.) (j) Glass slides with painted or frosted ends 1x3 inches 1mm (thick, precleaned.) How Do I Remove Asbestos Siding In North Carolina Cover Slips 22x22 mm, #1 1/2 (l) Paper clips or dissection needles (m) Hand grinder (n) Scalpel with both #10 and #11 blades (o) 0.1 molar HCl.

Decalcifying solution (Baxter Scientific Products) Ethylenediaminetetraacetic Acid, Tetrasodium, Sodium Potassium Tartrate, Hydrochloric Acid, Sodium Tartrate, Tetrahydrofuran (THF) (r) Hotplate capable of 60 deg.C (s) How Do I Remove Asbestos Siding In North Carolina Balance (t) Hacksaw blade (u) Ruby mortar and pestle 3.3. 

Sample Pre-Preparation Sample preparation begins with pre-preparation which may include chemical reduction of the matrix, heating the sample to dryness or heating in the muffle furnace. The end result is a How Do I Remove Asbestos Siding In North Carolina sample which has been reduced to a powder that is sufficiently fine to fit under the cover slip. 

Analyze different phases of samples separately, e.g., tile and the tile mastic should be analyzed separately as the mastic may contain asbestos while the tile may not. (a) Wet Samples. Samples with a high water content will not give the proper dispersion colors and must be dried prior to How Do I Remove Asbestos Siding In North Carolina sample mounting. 

Remove the lid of the scintillation vial, place the bottle in the drying oven and heat at 100 deg.C to dryness (usually about 2 h). Samples How Do I Remove Asbestos Siding In North Carolina which are not submitted to the lab in glass must be removed and placed in glass vials or aluminum weighing pans before placing them in the drying oven. (b) Samples With Organic Interference -- Muffle Furnace. 

These may include samples with tar as a matrix, vinyl asbestos tile, or any other organic that can be reduced by heating. Remove the sample from the vial and weigh in a balance to determine the weight of the submitted portion. Place the sample in a muffle furnace at 500 deg.C for 1 to 2 h or until all obvious organic How Do I Remove Asbestos Siding In North Carolina material has been removed. 

Retrieve, cool and weigh again to determine the weight loss on ignition. This is necessary to determine the asbestos content of the submitted sample, because the analyst will be looking at a reduced sample. Heating above 600 deg.C will cause the How Do I Remove Asbestos Siding In North Carolina sample to undergo a structural change which, given sufficient time, will convert the chrysotile to forsterite. 

Heating even at lower temperatures for 1 to 2 h may have a measurable effect on the optical properties of the minerals. If the analyst is unsure of what to expect, a How Do I Remove Asbestos Siding In North Carolina sample of standard asbestos should be heated to the same temperature for the same length of time so that it can be examined for the proper interpretation. 

Samples With Organic Interference -- THF Vinyl asbestos tile is the most common material treated with this solvent, although, substances containing tar will sometimes yield to this treatment. Select a portion of the material and then grind it up if possible. Weigh the sample and place How Do I Remove Asbestos Siding In North Carolina it in a test tube. Add sufficient THF to dissolve the organic matrix. 

This is usually about 4 to 5 mL. Remember, THF is highly flammable. Filter the remaining material through a tared silver membrane, dry and weigh to determine how much How Do I Remove Asbestos Siding In North Carolina is left after the solvent extraction. Further process the sample to remove carbonate or mount directly. (d) Samples With Carbonate Interference 

Carbonate material is often found on fibers and sometimes must be removed in order to perform dispersion microscopy. Weigh out a portion of the How Do I Remove Asbestos Siding In North Carolina material and place it in a test tube. Add a sufficient amount of 0.1 M HCl or decalcifying solution in the tube to react all the carbonate as evidenced by gas formation; i.e., when the gas bubbles stop, add a little more solution. 

If no more gas forms, the reaction is complete. Filter the How Do I Remove Asbestos Siding In North Carolina material out through a tared silver membrane, dry and weigh to determine the weight lost. 3.4. Sample Preparation Samples must be prepared so that accurate determination can be made of the asbestos type and amount present. 

The following steps are carried out in the low-flow hood (a low-flow hood has less than 50 fpm flow): (1) If the sample has large lumps, is hard, or cannot be made to lie under a cover slip, the grain size must be reduced. Place a small amount between two slides and grind the How Do I Remove Asbestos Siding In North Carolina material between them or grind a small amount in a clean mortar and pestle. 

The choice of whether to use an alumina, ruby, or diamond mortar depends on the hardness of the How Do I Remove Asbestos Siding In North Carolina material. Impact damage can alter the asbestos mineral if too much mechanical shock occurs. (Freezer mills can completely destroy the observable crystallinity of asbestos and should not be used). 

For some samples, a portion of material can be shaved off with a scalpel, ground off with a hand grinder or hack saw blade. The How Do I Remove Asbestos Siding In North Carolina preparation tools should either be disposable or cleaned thoroughly. Use vigorous scrubbing to loosen the fibers during the washing. Rinse the implements with copious amounts of water and air-dry in a dust-free environment. 

If the sample is powder or has been reduced as in (1) above, it is ready to mount. Place a glass slide on a piece of optical tissue and write the How Do I Remove Asbestos Siding In North Carolina identification on the painted or frosted end. Place two drops of index of refraction medium n = 1.550 on the slide. (The medium n = 1.550 is chosen because it is the matching index for chrysotile. 

Dip the end of a clean paper-clip or dissecting needle into the droplet of refraction medium on the slide to moisten it. Then dip the probe into the powder sample. Transfer what sticks on the probe to the slide. The How Do I Remove Asbestos Siding In North Carolina material on the end of the probe should have a diameter of about 3 mm for a good mount. If the material is very fine, less sample may be appropriate. 

For non-powder samples such as fiber mats, forceps should be used to transfer a small amount of How Do I Remove Asbestos Siding In North Carolina material to the slide. Stir the material in the medium on the slide, spreading it out and making the preparation as uniform as possible. 

Place a cover-slip on the preparation by gently lowering onto the slide and allowing it to fall "trapdoor" fashion on the How Do I Remove Asbestos Siding In North Carolina preparation to push out any bubbles. Press gently on the cover slip to even out the distribution of particulate on the slide. 

If there is insufficient mounting oil on the slide, one or two drops may be placed near the edge of the coverslip on the How Do I Remove Asbestos Siding In North Carolina slide. Capillary action will draw the necessary amount of liquid into the preparation. Remove excess oil with the point of a laboratory wiper

Clean Up Raw Sewage Carefully

This handbook has been prepared by the City of LaSalle to explain the causes of sewer backups that occur in the Sewage Cleanup Clean Up Raw Sewage Carefully City during sever rainstorms and to describe steps that are available to homeowners to prevent backups and to protect the contents of their house. 

  read more..

Animal Hoarders

BEHIND CLOSED DOORS: THE HORRORS OF ANIMAL HOARDERS By Rebecca Simmons To someone desperate to find a home for a litter of kittens, the Chubbers Animal Rescue would have appeared to be the perfect haven. Nestled in a wooded lot in Caroline County, Maryland, the former home of Linda Farve and Ernie M  read more..

Information About Mold

What are molds? Molds are microscopic organisms that live on plant or animal matter. They aid in the break down of dead material and recycle nutrients in the environment. Present virtually everywhere, they can be found growing on organic material such as soil, foods, and plant matter. In order to re  read more..

Grants For Ice Storm Tree Removal

Determine Management Options and Goals
Any disaster debris management plan should include a disposal strategy. Communities need to set priorities for recycling wastes and determine the desired disposal options for the remaining waste. Segregate Hazardous Waste - Be prepared to [M  read more..

Cures For Hoarders

Help for People who Hoard People who hoard benefit from behavioral health intervention and help in sorting and discarding the excess accumulation as well as storing what remains in a safe manner. Clean Up Clean up is a very delicate process because removing or even touching items without the person'  read more..

Mold Removal Procedures And Equipment

Molds are microscopic organisms found everywhere in the environment, indoors and outdoors. When present in large quantities, molds have the potential to cause adverse health effects. Health Effects of Mold Exposure Sneezing Cough and Mold Remediation Mold Removal Procedures And Equipment congestion Runny nose Aggravation of asthma Eye irr  read more..

Flood Water Contamination

What if I have already consumed potentially contaminated water?Illness is possible, especially for people that already have a chronic illness or may have compromised immune systems, for example, from AIDS or cancer treatments. This is why boil water notices are issued. Anyone experiencing symptoms s  read more..

Hazardous Materials From Clean Up Flood Damage

In all likelihood, hazardous materials will be encountered during the cleanup phase of the flood recovery effort: containers and other vessels that may hold materials that can either pose an immediate risk to cleanup crews if disturbed or might be classified as a hazardous waste for disposal purpose  read more..

Respirator Selection For Lead Dust Removal

Respirator Selection. (A) The employer shall select the appropriate respirator or combination of respirators from the following table. (B) The employer shall provide a powered, air purifying respirator in lieu of the respirator specified in Section 5198(f)(3)(A) whenever: 1. An Lead Paint Removal Respirator Selection For Lead Dust Removal employ  read more..

What Is The Best Way To Dry Out Carpets After A Ba

Extruded polystyrene, expanded polystyrene, and rigid mineral wool panels are routinely used in below-grade exterior foundation insulation systems. Extruded polystyrene has  read more..