Electronic Restoration >> Water Damage

Often, following some sort of water damage like a burst pipe or a thunderstorm that has caused damage to a house or business allowing water to enter creating a Water Damage. This will require the restoration of the electronic equipment that's in the building back to its original state. There are certain procedures that must be followed for electronic technicians to give them the ability to make these repairs and to complete a restoration.

  1. When working with high-tech computer equipment, the condition of the contacts could be affected and the condition of the dielectric insulation capabilities of internal materials might be reduced. Furthermore, some molded case circuit breakers are usually equipped with electronic might trip units and the functioning of these trip units could be impaired. For fuses, the water affect the filler material and a Water Damage filler material will most likely degrade the insulation and interruption capabilities. Distribution assemblies will contain protective components together with the necessary support structures, the bus work, the wiring, electromechanical or electronic relays and meters.
  2. Exposure to water could cause corrosion and insulation Water Damage to all of these areas. In the case of exposure of distribution assemblies to water damage, the manufacturer should be contacted before any further action is taken. Computer circuits include computer control devices such as circuit starters and contactors, together with overcurrent protection components like overload relays, circuit breakers, and fuses that often assembled into motor control panels and motor control centers as well as individual covers and enclosures. Motor control centers will contain both control and protective components together with sensitive support structures, the buswork, and the wiring.
  3. The protective components are very critical to the safe operation of motor circuits and their important ability to protect these circuits is adversely affected by exposure to Water Damage , and is to the minerals and the particles which could be present in the water. For molded case circuit breakers, such water exposure can affect the overall operation of the mechanism through corrosion, through the presence of foreign particles, and through removal of synthetic and lubricants. The condition of the contacts might be affected and the dielectric insulation capabilities of internal materials may be reduced. Furthermore, some molded case circuit breakers are equipped with electronic trip units, and the functioning of these trip units couldbe impaired. For fuses, the water may affect the filler material.
  4. A damaged filler material will degrade the insulation and the interruption capabilities. Corrosion, loss of lubrication, and insulation quality could also be expected in contactors and starters. However, the solid-state motor controllers and many of those electromechanical contactors or starters with integral electronic circuitry might be more severely affected by Water Damage. Drives damaged by water can be remanufactured by the original manufacturer specs in some cases. Electronically controlled and solid state contactors and starter components containing many semiconductors and transistors with overload relays that have molded case circuit breakers and molded case switches.

How To Damp Proof An Interior Basement Floor

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a   read more..

Water Extration Equipment For Roof Leaks

Does the State have a list of professional mold contractors?New York does not certify or license building contractors, Water Extraction Water Extration Equipment For Roof Leaks including mold contractors. 

If youhire a contractor to work on your flooded home and your home was built before 1978, checkwhether t  read more..

Wet Carpet From A Plumbing Leak

Common Indoor Moisture Sources Include: Flooding, inadequate maintenance and failure of building materials and systems Roof leaks Plumbing leaks Overflow from tubs, sinks or toilets Firewood stored indoors Humidifier use Inadequate venting of kitchen and Water Damage Wet Carpet From A Plumbing Leak bath humidity Improper venting  read more..

Roof Damage Insurance Claim In North Carolina

The primary key to good shingle performance is the use of self-seal adhesive, coupled with correct application of fasteners (Smith, 1994). With an adequate number of fasteners, the pull-through resistance of the shingle will determine whether the loss of adhesive seal leads to the shingle being lost  read more..

How To Check Soaked Carpet

Which types of carpeting need to be thrown away after water damage? Remove and throw away carpet soaked with "black water". Remove and throw away Water Damage How To Check Soaked Carpet carpet padding soaked with "gray" or "black water" (without exceptions). Carpet padding can be replaced if it has been soaked from clean water les  read more..

Smoke Damage

The fire combustion process when wood is burned is never quite complete and the Odor Control Smoke Damage from a wood burnt fire usually will contain a dark brown or black substance which has a very unpleasant odor. This tar looking substance is called creosote and is found almost anywhere in a wood house fir  read more..

Protect Your House From Animal Damage

Step 4. Determine if young are involved After finding the main entry you need to verify that no young are inside before proceeding with the eviction process. Because each situation and each animal is different, do this even if it seems early or late in the year for young to be present. Failing to do  read more..

How To Clean Up Raw Sewage In A Basement

Water from precipitation is not always the only source Basement Drying How To Clean Up Raw Sewage In A Basement of moisture. Urban development usually includes a centralized public water supply for the development. If the supply were through private domestic wells, then waterline leaks would be easy to identify. Simply turn off all the fauc  read more..

How To Remove Ice Storm Damage Debris In An Emerge

A monitor (usually located in a monitoring observation tower at the debris management site) assesses what percentage of the truck's volume is full of debris. This percentage is then multiplied by the truck's declared maximum volume (as previously certified and announced on a placard on the side of t  read more..

What Are Some Signs Of A Meth Lab

In a Tier 1 decontamination response, adult clothing and small washable fabricitems such as curtains, rugs and linens can be machine-washed twice with hot water anddetergent. After washing contaminated items, Meth Lab Cleanup What Are Some Signs Of A Meth Lab the washer shall be run once empty of clothing.
 
  read more..